M25P128-VMF6TP NUMONYX, M25P128-VMF6TP Datasheet - Page 10

IC FLASH 128MBIT 50MHZ 16SOIC

M25P128-VMF6TP

Manufacturer Part Number
M25P128-VMF6TP
Description
IC FLASH 128MBIT 50MHZ 16SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet

Specifications of M25P128-VMF6TP

Format - Memory
FLASH
Memory Type
FLASH
Memory Size
128M (16M x 8)
Speed
50MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
16-SOIC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25P128-VMF6TP
M25P128-VMF6TPTR

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M25P128-VMF6TP
Manufacturer:
Numonyx
Quantity:
11 000
Part Number:
M25P128-VMF6TP
Manufacturer:
ST
0
Part Number:
M25P128-VMF6TP
Manufacturer:
ST
Quantity:
20 000
Part Number:
M25P128-VMF6TPB
Manufacturer:
MICRON
Quantity:
4 500
Part Number:
M25P128-VMF6TPB
Manufacturer:
MICRON33
Quantity:
2 567
Part Number:
M25P128-VMF6TPB
Manufacturer:
MICRON/镁光
Quantity:
20 000
Part Number:
M25P128-VMF6TPB
0
Company:
Part Number:
M25P128-VMF6TPB
Quantity:
6 000
3
Figure 4.
1. The Write Protect (W/V
2. These pull-up resistors, R, ensure that the memory devices are not selected if the Bus Master leaves the S line in the high-
10/47
impedance state. As the Bus Master may enter a state where all inputs/outputs are in high impedance at the same time
(e.g.: when the Bus Master is reset), the clock line (C) must be connected to an external pull-down resistor so that, when all
inputs/outputs become high impedance, S is pulled High while C is pulled Low (thus ensuring that S and C do not become
High at the same time, and so, that the t
SPI Interface with
(CPOL, CPHA) =
CS3
(0, 0) or (1, 1)
SPI bus master
SPI modes
These devices can be driven by a microcontroller with its SPI peripheral running in either of
the two following modes:
For these two modes, input data is latched in on the rising edge of Serial Clock (C), and
output data is available from the falling edge of Serial Clock (C).
The difference between the two modes, as shown in
bus master is in Stand-by mode and not transferring data:
Bus master and memory devices on the SPI bus
CS2
CPOL=0, CPHA=0
CPOL=1, CPHA=1
C remains at 0 for (CPOL=0, CPHA=0)
C remains at 1 for (CPOL=1, CPHA=1)
CS1
PP
) and Hold (HOLD) signals should be driven, High or Low as appropriate.
SDO
SDI
SCK
R
(2)
R
(2)
SHCH
C Q D
S
SPI memory
requirement is met).
device
W/V
PP
V
CC
HOLD
R
V
(2)
SS
C Q D
S
SPI memory
device
W/V
Figure
PP
V
CC
HOLD
R
5, is the clock polarity when the
V
(2)
SS
C Q D
S
SPI memory
device
W/V
V
PP
CC
HOLD
AI12836
V
SS
V
V
CC
SS

Related parts for M25P128-VMF6TP