LTC1646CGN Linear Technology, LTC1646CGN Datasheet - Page 7

• Manufacturer Part Number: LTC1646CGN
• Description: IC CNTRLR HOTSWAP PCIDUAL 16SSOP
• Manufacturer: Linear Technology
• Type: Hot-Swap Controllerr

Specifications of LTC1646CGN

• Applications: CompactPCI™
• Internal Switch(s): No
• Voltage - Supply: 3.3V, 5V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP (0.150", 3.90mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

PI FU CTIO S
3V
resistor placed in the supply path between 3V
3V
a constant voltage across the sense resistor and a con-
stant current through the switch while the TIMER pin
voltage is less than 1.25V. A foldback feature makes the
current limit decrease as the voltage at the 3V
approaches GND.
When the TIMER pin voltage exceeds 1.25V, the circuit
breaker function is enabled. If the voltage across the sense
resistor exceeds 56mV, the circuit breaker is tripped after
a 21µs time delay. In the event the sense resistor voltage
exceeds 150mV, the circuit breaker trips immediately and
the chip latches off. To disable the 3.3V current limit,
3V
GATE (Pin 10): High Side Gate Drive for the External 3.3V
and 5V N-Channel pass transistors. Requires an external
series RC network for the current limit loop compensation
and setting the minimum ramp-up rate. During power-up,
the slope of the voltage rise at the GATE is set by the 13µA
current source connected to the internal charge pump and
the external capacitor connected to GND or by the 3.3V or
5V current limit and the bulk capacitance on the 3V
5V
ramp down voltage is set by the 200µA current source
connected to GND and the external GATE capacitor.
The voltage at the GATE pin will be modulated to maintain
a constant current when either the 3V or 5V supplies go
into current limit while the TIMER pin voltage is less than
1.25V. If a current fault occurs after the TIMER pin voltage
exceeds 1.25V, the GATE pin is immediately pulled to
GND.
5V
resistor placed in the supply path between 5V
5V
a constant voltage across the sense resistor and a con-
stant current through the switch while the TIMER pin
voltage is less than 1.25V. A foldback feature makes the
current limit decrease as the voltage at the 5V
approaches GND.
SENSE
SENSE
SENSE
OUT
SENSE
SENSE
U
supply lines. During power-down, the slope of the
, the GATE pin voltage will be adjusted to maintain
, the GATE pin voltage will be adjusted to maintain
and 3V
(Pin 9): 3.3V Current Limit Set. With a sense
(Pin 11): 5V Current Limit Set. With a sense
U
IN
can be shorted together.
U
OUT
OUT
IN
IN
OUT
and
and
pin
pin
or
When the TIMER pin voltage is greater than 1.25V, the
circuit breaker function is enabled. If the voltage across
the sense resistor exceeds 56mV but is less than 150mV,
the circuit breaker is tripped after a 21µs time delay. In the
event the sense resistor voltage exceeds 150mV, the
circuit breaker trips immediately and the chip latches off.
To disable the 5V current limit, short 5V
together.
5V
lockout circuit prevents the GATE pin voltage from
ramping up when the voltage at the 5V
2.5V. If no 5V input supply is available, tie the 5V
the 3V
PRECHARGE (Pin 13): Precharge Monitor Input. An on-
chip error amplifier with a 1V reference servos the DRIVE
pin voltage to keep the precharge node at 1V. If the
precharge function is not being used, tie the PRECHARGE
pin to GND.
DRIVE (Pin 14): Precharge Base Drive Output. Provides
base drive for an external NPN emitter-follower which in
turn biases the PRECHARGE node. If the precharge func-
tion is not being used, allow the DRIVE pin to float.
OFF/ON (Pin 15): Digital Input. Connect the CPCI BD_SEL#
signal to the OFF/ON pin. When the OFF/ON pin is pulled
low, the GATE pin is pulled high by a 13µA current source.
When the OFF/ON pin is pulled high the GATE pin will be
pulled to ground by a 200µA current source.
The OFF/ON pin is also used to reset the electronic circuit
breaker. If the OFF/ON pin is cycled high and low following
the trip of the circuit breaker, the circuit breaker is reset,
and a normal power-up sequence will occur.
RESETIN (Pin 16): Digital Input. Connect the CPCI
PCI_RST# signal to the RESETIN pin. Pulling RESETIN low
will cause the RESETOUT pin to pull low.
IN
(Pin 12): 5V Supply Sense Input. An undervoltage
IN
pin.
IN
LTC1646
SENSE
pin is less than
and 5V
IN
pin to
1646fa
7
IN