ISL6218CV Intersil, ISL6218CV Datasheet - Page 5

• Manufacturer Part Number: ISL6218CV
• Description: IC CTRLR INTEL PENT M 38-TSSOP
• Manufacturer: Intersil

Specifications of ISL6218CV

• Applications: Processor
• Current - Supply: 1.4mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -10°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 38-TSSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Functional Pin Description 38 Ld TSSOP
VDD
This pin is used to connect +5V to the IC to supply all power
necessary to operate the chip. The IC starts to operate when
the voltage on this pin exceeds the rising POR threshold and
shuts down when the voltage on this pin drops below the
falling POR threshold.
VDDP
This pin provides a low ESR bypass connection to the
internal gate drivers for the +5V source.
PGOOD
This pin is used as an input and an output and is tied to the
Vccp and Vcc_mch PGOOD signals. During start-up, this pin
is recognized as an input, and prevents further slewing of the
output voltage from the “Boot” level until PGOOD from Vccp
and Vcc_mch is enabled High. After start-up, this pin has an
open drain output used to indicate the status of the CORE
output voltage. This pin is pulled low when the system output
is outside of the regulation limits. PGOOD includes a timer
for power-on delay.
EN
This pin is connected to the system signal VR_ON and
provides the enable/disable function for the PWM controller.
OCSET
A resistor from this pin to ground sets the overcurrent
protection threshold. The current from this pin should be
between 10µA and 25µA (70kΩ to 175kΩ equivalent
pull-down resistance).
DACOUT
PGOOD
DRSEN
COMP
DSEN
SOFT
FSET
VDD
VID0
VID1
VID2
VID3
VID4
VID5
DSV
EA+
NC
EN
FB
10
11
12
13
14
15
16
17
18
19
1
2
3
4
5
6
7
8
9
ISL6218
5
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
VBAT
ISEN
PHASE
UG
BOOT
VSSP
LG
VDDP
NC
NC
NC
NC
NC
NC
VSEN
DRSV
STV
OCSET
VSS
ISL6218
VSEN
This pin is used for remote sensing of the microprocessor
CORE voltage.
COMP
This pin provides connection to the error amplifier output.
FB
This pin is connected to the inverting input of the error
amplifier.
EA+
This pin is connected to the non-inverting input of the error
amplifier and is used for setting the “Droop” voltage.
STV
The voltage on this pin sets the initial start-up or “Boot”
voltage.
SOFT
This pin programs the slew rate of VID changes, Deep Sleep
and Deeper Sleep transitions, and soft-start after initializing.
This pin is connected to ground via a capacitor, and to EA+
through an external “Droop” resistor.
DSEN
This pin connects to system logic “STP_CPU” and enables
Deep Sleep mode of operation. Deep Sleep is enabled when
a logic LOW signal is detected on this pin.
DRSEN
This pin connects to system logic “DPRSLPVR” and enables
Deeper Sleep mode of operation when a logic HIGH is
detected on this pin.
VBAT
Voltage on this pin provides feed-forward battery information
that adjusts the oscillator ramp amplitude.
FSET
A resistor from this pin to ground programs the switching
frequency.
ISEN
This pin is used as current sense input from the converter
channel phase node.
DACOUT
This pin provides access to the output of the Digital-to-
Analog Converter.
DSV
The voltage on this pin provides the setpoint for output
voltage during Deep Sleep Mode of operation.
DRSV
The voltage on this pin provides the setpoint for output
voltage during Deeper Sleep Mode of operation.
August 6, 2007
FN9101.6