TLE4250-2G Infineon Technologies, TLE4250-2G Datasheet
TLE4250-2G
Specifications of TLE4250-2G
TLE4250-2G
TLE4250-2GTR
Available stocks
Related parts for TLE4250-2G
TLE4250-2G Summary of contents
Page 1
...
Page 2
... V are regulated to a reference voltage applied at the adjust input “ADJ” with high I accuracy. The output “Q” is able to drive loads mA. In order to reduce the quiescent current to a minimum, the TLE4250-2 can be switched to stand-by mode by setting the adjust/enable input “ADJ/EN” to “low”. Type TLE4250-2G Data sheet V + ...
Page 3
... Range”. 5 GND Ground Reference. Internally connected to Pin 2. Connect to heatsink area. Data sheet TLE 4250-2 Saturation Control Temp. Current Limitation Protection GND ADJ/ GND GND ut TLE4250-2 Block Diagram Regulated Output Voltage Q C off-board Q load Rev. 1.0, 2007-07-24 ...
Page 4
... Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Data sheet General Product Characteristics Symbol Limit Values Min. Max -0.3 40 ADJ/EN T -40 150 j T -50 150 stg ESD,HBM ESD,CDM 4 TLE4250-2 Unit Conditions V – V – V – C – C – HBM 3) kV CDM Rev. 1.0, 2007-07-24 ...
Page 5
... Limit Value Min. Typ. Max. R – 81 – thJA – 217 – – 117 – – 103 – R – 30 – thJSP 5 TLE4250-2 General Product Characteristics Unit Conditions V – V – C – 1) µF – 2) – Unit Conditions 1) K/W 2s2p board 2) K/W Footprint only 2 K/W ...
Page 6
... Please note that a junction temperature above 150 °C is outside the maximum ratings and reduces the IC lifetime. The TLE4250-2 allows a negative supply voltage. However, several small currents are flowing into the IC. For details see electrical characteristics table and typical performance graphs. The thermal protection circuit is not operating during reverse polarity condition ...
Page 7
... Data sheet T 150 C; all voltages with respect to ground (unless otherwise specified). j Symbol Limit Values Min. Typ. Max – -10 -2 – 151 – 200 j,eq V has dropped 100 mV from its nominal value TLE4250-2 Electrical Characteristics Unit Conditions ADJ - ADJ T °C increasing due to power j ...
Page 8
... [mA] ADJ Data sheet Output Voltage Input Voltage VQ-VADJ.vsd V [ [V] ADJ Line Regulation d Input Voltage Change d SOA.VSD V [mV ° 0 125 °C j 0 TLE4250-2 Electrical Characteristics -40 ° 150 ° vs. Q,line I,initial ADJ steady-state condition Rev. 1.0, 2007-07-24 VQ-VI.vsd [V] dVQ-dVI.vsd 40 V [V] ...
Page 9
... Output Capacitor Series Resistor vs. Output Current dVQ-dIQ.vsd 10 ESR Q,initial [ ] ADJ °C j 0.1 0. [mA] Q Load Transient Response dVI-reponse.vsd V Q [mV] 0 -50 Q [mA [µs] 9 TLE4250-2 Electrical Characteristics ESR 2.2 µ µF Q Stable Region V < -40 °C < < 150 ° dIQresponse.vsd ADJ C = 2.2 µF Ceramic ...
Page 10
... Dropout Voltage Output Current dVQ-Tj.vsd V [mV 100 100 120 140 T [°C] j Output Current Limitation vs. Output Voltage Vdr-Tj.vsd V [ 100 120 140 T [° Electrical Characteristics V vs 150 ° ° Q,max 13 ADJ 125° Rev. 1.0, 2007-07-24 TLE4250-2 Vdr-IQ_log.vsd 50 I [mA] Q IQmax-VQ.vsd = 25°C j 100 I [mA] Q ...
Page 11
... RIPPLE 2.2 µF Ceramic °C j 0.01 0.1 1 Data sheet Reverse Current Input Voltage IQ-VQ.vsd +0.5 I [mA ADJ -0 -40 ° [V] Q PSRR.vsd 100 f [kHz] 11 Electrical Characteristics I vs ADJ T = -40 ° 150 ° -32 -24 -16 -8 Rev. 1.0, 2007-07-24 TLE4250-2 II-VI.vsd 0 V [V] I ...
Page 12
... C; all voltages with respect to ground (unless otherwise specified). j Symbol Limit Values Min. Typ. I – – 140 q2 – – Current Consumption Output Current Iq-Tj.vsd I [mA 0.1 80 100 120 140 T [° Electrical Characteristics Unit Conditions Max µA 0.4 V; ADJ/ 200 µ ADJ vs EN/ADJ 13 Rev. 1.0, 2007-07-24 TLE4250-2 Iq-IQ.vsd [mA] Q ...
Page 13
... I Current Consumption vs Input Voltage [mA Data sheet Iq-VI.vsd ADJ = [ TLE4250-2 Electrical Characteristics Rev. 1.0, 2007-07-24 ...
Page 14
... Adjust / Enable Input In order to reduce the quiescent current to a minimum, the TLE4250-2G can be switched to stand-by mode by setting the adjust/enable input “ADJ/EN” to “low”. Table 3 Electrical Characteristics Adjust / Enable 13.5 V; 2 ADJ all voltages with respect to ground, positive current flowing into pin (unless otherwise specified). ...
Page 15
... DIN 6784 +0.1 0.3 -0.05 0.95 1.9 1) Contour of slot depends on profile gull-wing lead form 0.4 HLG09053 16 TLE4250-2 Package Outlines 1.1 MAX. 0.1 MAX. A +0.1 0.15 -0.06 0 GPW05997 2.3 1.3 1.45 0.4 0.75 0.95 HLG09090 Wave Soldering Dimensions in mm ...
Page 16
... Revision History Revision Date Changes Rev. 1.0 2007-07-24 • Data sheet Final Datasheet Initial Version 17 TLE4250-2 Revision History Rev. 1.0, 2007-07-24 ...
Page 17
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...