HIP6302CBZ Intersil, HIP6302CBZ Datasheet - Page 10

• Manufacturer Part Number: HIP6302CBZ
• Description: IC CONTROLLER PWM BUCK 16-SOIC
• Manufacturer: Intersil

Specifications of HIP6302CBZ

• Pwm Type: Controller
• Number Of Outputs: 2
• Frequency - Max: 305kHz
• Voltage - Supply: 4.75 V ~ 5.25 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 16-SOIC (3.9mm Width)
• Frequency-max: 305kHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Duty Cycle: -

Under-Voltage
The VSEN pin also detects when the CORE voltage falls
more than 10% below the VID programmed level. This
causes PGOOD to go low, but has no other effect on
operation and is not latched. There is also hysteresis in this
detection point.
Over-Current
In the event of an over-current condition, the over-current
protection circuit reduces the average current delivered to
less than 25% of the current limit. When an over-current
condition is detected, the controller forces all PWM outputs
into a three state mode. This condition results in the gate
driver removing drive to the output stages.The HIP6302
goes into a wait delay timing cycle that is equal to the Soft-
Start ramp time. PGOOD also goes “low” during this time
due to VSEN going below its threshold voltage.To lower the
average output dissipation, the Soft-Start initial wait time is
increased from 32 to 2048 cycles, then the Soft-Start ramp is
initiated. At a PWM frequency of 200kHz, for instance, an
over-current detection would cause a dead time of 10.24ms,
then a ramp of 10.08ms.
At the end of the delay, PWM outputs are restarted and the
Soft-Start ramp is initiated. If a short is present at that time,
the cycle is repeated. This is the hiccup mode.
Figure 6 shows the supply shorted under operation and the
hiccup operating mode described above. Note that due to
the high short circuit current, over-current is detected before
completion of the start-up sequence so the delay is not quite
as long as the normal Soft-Start cycle.
FIGURE 6. SHORT APPLIED TO SUPPLY AFTER POWER-UP
SHORT APPLIED HERE
HICCUP MODE. SUPPLY POWERED BY ATX SUPPLY
ATX SUPPLY ACTIVATED BY ATX “PS-ON PIN”
CORE LOAD CURRENT = 31A, 5V LOAD = 5A
SUPPLY FREQUENCY = 200kHz, V
10
IN
= 12V
PGOOD
SHORT
CURRENT
50A/DIV
HIP6302
HIP6302
CORE Voltage Programming
The voltage identification pins (VID0, VID1, VID2, VID3 and
VID4) set the CORE output voltage. Each VID pin is pulled to
V
collector/open-drain/open-switch-to-ground or standard low-
voltage TTL or CMOS signals.
Table 1 shows the nominal DAC voltage as a function of the
VID codes. The power supply system is ±1% accurate over
the operating temperature and voltage range.
CC
VID4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
by an internal 20µA current source and accepts open-
TABLE 1. VOLTAGE IDENTIFICATION CODES
VID3
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
VID2
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
VID1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
VID0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
December 27, 2004
VDAC
1.100
1.125
1.150
1.175
1.200
1.225
1.250
1.275
1.300
1.325
1.350
1.375
1.400
1.425
1.450
1.475
1.500
1.525
1.550
1.575
1.600
1.625
1.650
1.675
1.700
1.725
1.750
1.775
1.800
1.825
1.850
FN4766.3
Off