HIP6021CBZ Intersil, HIP6021CBZ Datasheet - Page 14

• Manufacturer Part Number: HIP6021CBZ
• Description: IC PWM TRPL PWR CONTROL 28-SOIC
• Manufacturer: Intersil

Specifications of HIP6021CBZ

• Pwm Type: Voltage Mode
• Number Of Outputs: 4
• Frequency - Max: 215kHz
• Duty Cycle: 100%
• Voltage - Supply: 10.8 V ~ 13.2 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: Yes
• Cuk: No
• Isolated: No
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 28-SOIC (7.5mm Width)
• Frequency-max: 215kHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

each drive a MOSFET or a NPN bipolar as a pass transistor.
All these transistors should be selected based upon
r
requirements, and thermal management considerations.
PWM MOSFET Selection and Considerations
In high-current PWM applications, the MOSFET power
dissipation, package selection and heatsink are the
dominant design factors. The power dissipation includes two
loss components; conduction loss and switching loss. These
losses are distributed between the upper and lower
MOSFETs according to duty factor (see the equations
below). The conduction losses are the main component of
power dissipation for the lower MOSFETs. Only the upper
MOSFET has significant switching losses, since the lower
device turns on and off into near zero voltage.
The equations below assume linear voltage-current
transitions and do not model power loss due to the reverse-
recovery of the lower MOSFET’s body diode. The gate-
charge losses are dissipated by the HIP6021 and don't heat
the MOSFETs. However, large gate-charge increases the
switching time, t
switching losses. Ensure that both MOSFETs are within their
maximum junction temperature at high ambient temperature
by calculating the temperature rise according to package
thermal-resistance specifications. A separate heatsink may
be necessary depending upon MOSFET power, package
type, ambient temperature and air flow.
The r
the same device is used for both. This is because the gate
drive applied to the upper MOSFET is different than the
lower MOSFET. Figure 11 shows the gate drive where the
upper MOSFET’s gate-to-source voltage is approximately
VCC less the input supply. For +5V main power and +12VDC
for the bias, the gate-to-source voltage of Q1 is 7V. The
lower gate drive voltage is +12VDC. A logic-level MOSFET is
a good choice for Q1 and a logic-level MOSFET can be used
for Q2 if its absolute gate-to-source voltage rating exceeds
the maximum voltage applied to VCC.
Rectifier CR1 is a clamp that catches the negative inductor
swing during the dead time between the turn off of the lower
MOSFET and the turn on of the upper MOSFET. The diode
must be a Schottky type to prevent the lossy parasitic
DS(ON)
P
P
UPPER
LOWER
DS(ON)
, current gain, saturation voltages, gate supply
=
=
is different for the two equations above even if
I
----------------------------------------------------------- -
I
-------------------------------------------------------------------------------- -
O
O
SW
2
2
×
×
r
r
which increases the upper MOSFET
DS ON
DS ON
V
(
(
IN
)
V
)
×
×
IN
14
V
(
V
OUT
IN
–
+
V
I
----------------------------------------------------
OUT
O
×
V
)
IN
×
2
t
SW
×
F
S
HIP6021
FIGURE 11. UPPER GATE DRIVE - DIRECT V
MOSFET body diode from conducting. It is acceptable to
omit the diode and let the body diode of the lower MOSFET
clamp the negative inductor swing, but efficiency could drop
one or two percent as a result. The diode's rated reverse
breakdown voltage must be greater than the maximum input
voltage.
Linear Controller Transistor Selection
The main criteria for selection of transistors for the linear
regulators is package selection for efficient removal of heat.
The power dissipated in a linear regulator is:
Select a package and heatsink that maintains the junction
temperature below the rating with a the maximum expected
ambient temperature.
When selecting bipolar NPN transistors for use with the
linear controllers, insure the current gain at the given
operating VCE is sufficiently large to provide the desired
output load current when the base is fed with the minimum
driver output current.
P
LINEAR
HIP6021
-
+
+12V
=
I
O
×
VCC
(
V
GND
IN
UGATE
PHASE
LGATE
PGND
–
V
OUT
)
Q1
Q2
+5V OR LESS
CR1
CC
NOTE:
V
NOTE:
V
GS
DRIVE OPTION
GS
≈
≈
V
V
CC
CC
-5V