IRU3007CW International Rectifier, IRU3007CW Datasheet - Page 5

• Manufacturer Part Number: IRU3007CW
• Description: IC CTRL/REG SYNC BUCK 28-SOIC
• Manufacturer: International Rectifier

Specifications of IRU3007CW

• Applications: Controller, Intel Pentium® II
• Voltage - Input: 5V, 12V
• Number Of Outputs: 4
• Voltage - Output: 1.3 ~ 3.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *IRU3007CW; IRU3007-CW; IRU3007-CW

PIN#
Rev. 2.1
08/20/02
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PIN SYMBOL
Fault / Rt
OCSet1
Phase1
UGate1
LGate1
Gate3
V
PGnd
V
V
Gnd
V12
Fb2
Fb4
Fb3
Fb1
SS
NC
V5
OUT
SEN
SEN
2
4
1
This pin provides the feedback for the non-synchronous switching regulator. A resistor
divider is connected from this pin to V
value of the resistor connected from V
5V supply voltage. A high frequency capacitor (0.1 to 1mF) must be placed close to this
pin and connected from this pin to the ground plane for noise free operation.
This pin provides the soft-start for the 2 switching regulators. An internal resistor charges
an external capacitor that is connected from 5V supply to this pin which ramps up the
outputs of the switching regulators, preventing the outputs from overshooting as well as
limiting the input current. The second function of the Soft-Start cap is to provide long off
time (HICCUP) for the synchronous MOSFET during current limiting.
This pin has dual function. It acts as an output of the OVP circuitry or it can be used to
program the frequency using an external resistor. When used as a fault detector, if any of
the switcher outputs exceed the OVP trip point, the Fault pin switches to 12V and the
soft-start cap is discharged. If the Fault pin is to be connected to any external circuitry,
it needs to be buffered as shown in the application circuit.
This pin provides the feedback for the internal LDO regulator that its output is V
This pin is connected to the output of the I/O switching regulator. It is an input that
provides sensing for the Under/Over-voltage circuitry for the I/O supply as well as the
power for the internal LDO regulator.
This pin is the output of the internal LDO regulator.
This pin serves as the ground pin and must be connected directly to the ground plane.
This pin controls the gate of an external transistor for the 1.5V GTL+ linear regulator.
This pin provides the feedback for the linear regulator that its output drive is Gate3.
No connection.
This pin provides the feedback for the synchronous switching regulator. Typically this pin
can be connected directly to the output of the switching regulator. However, a resistor
divider is recommended to be connected from this pin to V
output voltage for any drop in the output voltage that is caused by the trace resistance.
The value of the resistor connected from V
This pin is internally connected to the undervoltage and overvoltage comparators sensing
the Vcore status. It must be connected directly to the Vcore supply.
This pin is connected to the Drain of the power MOSFET of the Core supply and it
provides the positive sensing for the internal current sensing circuitry. An external resis-
tor programs the CS threshold depending on the R
capacitor is placed in parallel with the programming resistor to provide high frequency
noise filtering.
This pin serves as the Power ground pin and must be connected directly to the ground
plane close to the source of the synchronous MOSFET. A high frequency capacitor
(typically 1mF) must be connected from V12 pin to this pin for noise free operation.
Output driver for the synchronous power MOSFET for the Core supply.
This pin is connected to the Source of the power MOSFET for the Core supply and it
provides the negative sensing for the internal current sensing circuitry.
Output driver for the high-side power MOSFET for the Core supply.
This pin is connected to the 12V supply and serves as the power Vcc pin for the output
drivers. A high frequency capacitor (typically 1mF) must be placed close to this pin and
PGnd pin and be connected directly from this pin to the ground plane for noise free
operation.
PIN DESCRIPTION
www.irf.com
OUT
OUT
2 and ground that sets the output voltage. The
2 to Fb2 must be less than 100V.
OUT
1 to Fb1 must be less than 100V.
DS
of the power MOSFET. An external
OUT
1 and ground to adjust the
IRU3007
OUT
4.
5