LM2825N-5.0/NOPB National Semiconductor, LM2825N-5.0/NOPB Datasheet
LM2825N-5.0/NOPB
Specifications of LM2825N-5.0/NOPB
*LM2825N-5.0/NOPB
LM2825N-5.0
Related parts for LM2825N-5.0/NOPB
LM2825N-5.0/NOPB Summary of contents
Page 1
... Efficient pre-regulator for linear regulators n Distributed power systems n DC/DC module replacement Connection Diagram DS012661-27 “NC (Do not use)” pins: See Figure 11 . Top View DS012661-1 Ordering Information Order Number LM2825N-3.3, LM2825N-5.0, LM2825N-12, LM2825N-ADJ or LM2825HN-ADJ See NS Package Number NA24F May 1997 typically 65 µA Q DS012661-2 www.national.com ...
Page 2
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Maximum Input Supply ( SD/SS Pin Input Voltage (Note 2) Output Pin Voltage (3.3V, 5.0V and ADJ) (12V and H-ADJ) ADJ Pin Voltage (ADJ, H-ADJ only) ...
Page 3
LM2825-12 Electrical Characteristics Specifications with standard type face are for T ture Range. Test Circuit Figure 2 . Symbol Parameter V Output Voltage 15V OUT Line Regulation 15V I LOAD Load Regulation 0.1A = 24V 24V, I ...
Page 4
All Output Voltage Versions Electrical Characteristics Specifications with standard type face are for T = 12V for 3.3V, 5.0V and ADJ versions, V less otherwise specified Symbol Parameter I DC Output Current Limit SD/SS Pin ...
Page 5
Typical Performance Characteristics = 12V for 3.3V, 5.0V and ADJ versions Normalized Output Voltage DS012661-3 Line Regulation DS012661-6 Operating Quiescent Current DS012661-9 (Circuits of Figure 2 and Figure 3 ) Unless otherwise specified, = 24V for 12V ...
Page 6
Typical Performance Characteristics = 12V for 3.3V, 5.0V and ADJ versions Soft-start DS012661-12 Switch Current Limit Load Transient Response for Continuous Mode = 20V 5V 250 mA to 750 OUT ...
Page 7
Test Circuit * Optional—Required if package is more than 6" away from main filter or bypass capacitor. * *Optional Soft-start Capacitor = 40V (max 3. 12V @ 0.75A OUT * Optional—Required ...
Page 8
Application Information It is especially useful in situations where the input power source is limited in the amount of current it can deliver, since you avoid loading down this type of power supply. Under some operating conditions, a Soft-start capacitor ...
Page 9
Application Information (Continued) = −40˚C to −25˚C AND T OUTPUT CURRENT DERATING FOR the lower temperature extremes, the switch current limit drops off sharply result, a lower output current is available in this temperature range. ...
Page 10
Application Information OUTPUT CURRENT DERATING FOR T Due to the limited switch current, the LM2825 cannot supply the full one ampere output current over the entire input and output voltage range. Figure 8 shows the typical available output current for ...
Page 11
Application Information (Continued) FIGURE 10. Typical Circuits Using Shutdown /Soft-start Features TYPICAL THROUGH HOLE PC BOARD LAYOUT (2X SIZE), SINGLE SIDED, THROUGH HOLE PLATED Note: Holes are not shown. “No Connect Pins” are connected to copper pads for thermal reasons ...
Page 12
... Physical Dimensions inches (millimeters) unless otherwise noted 24-Lead (0.600" Wide) Molded Dual-In-Line Package Order Number LM2825N-3.3, LM2825N-5.0, LM2825N12, LM2825N-ADJ or LM2825HN-ADJ LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE- VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI- CONDUCTOR CORPORATION ...