LTC1709EG-8 Linear Technology, LTC1709EG-8 Datasheet - Page 24

• Manufacturer Part Number: LTC1709EG-8
• Description: IC REG SW 2PH SYNC STPDWN 36SSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC1709EG-8

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 2
• Voltage - Output: 1.3 ~ 3.5 V
• Current - Output: 3A
• Voltage - Input: 4 ~ 36 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 36-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power - Output: -
• Frequency - Switching: -

LTC1709-8/LTC1709-9
APPLICATIO S I FOR ATIO
Using Figure 4, the RMS ripple current will be:
An input capacitor(s) with a 4.6A
is required.
The output capacitor ripple current is calculated by using
the inductor ripple already calculated for each inductor
and multiplying by the factor obtained from Figure 3
along with the calculated duty factor. The output ripple in
continuous mode will be highest at the maximum input
voltage since the duty factor is < 50%. The maximum
output current ripple is:
PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC1709. These items are also illustrated graphically in
the layout diagram of Figure 10. Check the following in
your layout:
1) Are the signal and power grounds segregated? The
LTC1709 signal ground pin should return to the (–) plate
of C
sources of the bottom N-channel MOSFETs, anodes of the
Schottky diodes, and (–) plates of C
as short lead lengths as possible.
2) Does the LTC1709 V
load? Does the LTC1709 V
return?
3) Are the SENSE
minimum PC trace spacing? The filter capacitors between
SENSE
possible to the LTC1709. Ensure accurate current sensing
with Kelvin connections at the current sense resistor.
24
I
V
INRMS
OUTRIPPLE
OUT
I
I
COUT
COUTMAX
+
separately. The power ground returns to the
and SENSE
= (20A)(0.23) = 4.6A
V
OUT
fL
1 2
–
20
300
.
and SENSE
U
m
0 3
A
–
.
RMS
kHz
pin pairs should be as close as
1 8
OS
at
1 2
.
U
.
+
33
V
1 5
OS
A
pin connect to the point of
.
+
RMS
%
–
RMS
leads routed together with
RMS
D F
pin connect to the load
H
IN
W
0 3
ripple current rating
.
, which should have
24
mV
RMS
U
4) Does the (+) plate of C
topside MOSFETs as closely as possible? This capacitor
provides the AC current to the MOSFETs. Keep the input
current path formed by the input capacitor, top and bottom
MOSFETs, and the Schottky diode on the same side of the
PC board in a tight loop to minimize conducted and
radiated EMI.
5) Is the INTV
nected closely between INTV
This capacitor carries the MOSFET driver peak currents. A
small value is recommended to allow placement immedi-
ately adjacent to the IC.
6) Keep the switching nodes, SW1 (SW2), away from
sensitive small-signal nodes. Ideally the switch nodes
should be placed at the furthest point from the LTC1709.
7) Use a low impedance source such as a logic gate to drive
the PLLIN pin and keep the lead as short as possible.
The diagram in Figure 10 illustrates all branch currents in
a 2-phase switching regulator. It becomes very clear after
studying the current waveforms why it is critical to keep
the high-switching-current paths to a small physical size.
High electric and magnetic fields will radiate from these
“loops” just as radio stations transmit signals. The output
capacitor ground should return to the negative terminal of
the input capacitor and not share a common ground path
with any switched current paths. The left half of the circuit
gives rise to the “noise” generated by a switching regula-
tor. The ground terminations of the sychronous MOSFETs
and Schottky diodes should return to the negative plate(s)
of the input capacitor(s) with a short isolated PC trace
since very high switched currents are present. A separate
isolated path from the negative plate(s) of the input
capacitor(s) should be used to tie in the IC power ground
pin (PGND) and the signal ground pin (SGND). This
technique keeps inherent signals generated by high cur-
rent pulses from taking alternate current paths that have
finite impedances during the total period of the switching
regulator. External OPTI-LOOP compensation allows over-
compensation for PC layouts which are not optimized but
this is not the recommended design procedure.
CC
1 F ceramic decoupling capacitor con-
IN
CC
connect to the drains of the
and the power ground pin?