LM2587SX-ADJ/NOPB National Semiconductor, LM2587SX-ADJ/NOPB Datasheet - Page 25

• Manufacturer Part Number: LM2587SX-ADJ/NOPB
• Description: IC MULTI CONFIG ADJ 5A TO-263-5
• Manufacturer: National Semiconductor
• Series: SIMPLE SWITCHER®r
• Type: Step-Up (Boost), Flyback, Forward Converterr

Specifications of LM2587SX-ADJ/NOPB

• Internal Switch(s): Yes
• Synchronous Rectifier: No
• Number Of Outputs: 1
• Voltage - Output: Adjustable
• Current - Output: 5A
• Frequency - Switching: 100kHz
• Voltage - Input: 4 ~ 40 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: D²Pak, TO-263 (5 leads + tab)
• Dc To Dc Converter Type: Step Up
• Pin Count: 5 +Tab
• Input Voltage: 40V
• Output Voltage: 1.23V
• Switching Freq: 115KHz
• Efficiency: 90%
• Package Type: TO-263
• Output Type: Adjustable
• Switching Regulator: Yes
• Load Regulation: 100mV
• Line Regulation: 100mV
• Mounting: Surface Mount
• Input Voltage (min): 4V
• Operating Temperature Classification: Automotive
• For Use With: 551011367-061 - BOARD WEBENCH LM2577,LM2585/87LM2587EVAL - EVALUATION BOARD FOR LM2587
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -
• Lead Free Status / Rohs Status: Compliant
• Other names: *LM2587SX-ADJ; *LM2587SX-ADJ/NOPB; LM2587SX-ADJ

4) LM2587 package thermal resistances θ
in the Electrical Characteristics).
Total power dissipated (P
as follows:
Boost:
V
N is the transformer turns ratio, D is the duty cycle, and
I
the maximum load currents for multiple-output flyback regu-
lators). The duty cycle is given by:
Boost:
where V
typically 0.5V for Schottky diodes and 0.8V for fast recovery
diodes. V
in the Characteristic Curves.
When no heat sink is used, the junction temperature rise is:
Adding the junction temperature rise to the maximum ambient
temperature gives the actual operating junction temperature:
If the operating junction temperature exceeds the maximum
junction temperatue in item 3 above, then a heat sink is re-
LOAD
IN
is the minimum input voltage, V
is the maximum load current (and
F
SAT
is the forward biased voltage of the diode and is
is the switch saturation voltage and can be found
ΔT
T
J
D
J
= ΔT
) by the LM2587 can be estimated
= P
D
J
× θ
+ T
OUT
JA
A
.
.
is the output voltage,
∑
I
LOAD
JA
and θ
is the sum of
JC
(given
25
quired. When using a heat sink, the junction temperature rise
can be determined by the following:
Again, the operating junction temperature will be:
As before, if the maximum junction temperature is exceeded,
a larger heat sink is required (one that has a lower thermal
resistance).
Included in the Switchers Made Simple design software is a
more precise (non-linear) thermal model that can be used to
determine junction temperature with different input-output pa-
rameters or different component values. It can also calculate
the heat sink thermal resistance required to maintain the reg-
ulator junction temperature below the maximum operating
temperature.
To further simplify the flyback regulator design procedure,
National Semiconductor is making available computer design
software. Switchers Made Simple software is available on
a (3½ ) diskette for IBM compatable computers from a Na-
tional Semiconductor sales office in your area or the National
Semiconductor
(1-800-272-9959).
European Magnetic Vendor
Contacts
Please contact the following addresses for details of local
distributors or representatives:
Coilcraft
21 Napier Place
Wardpark North Cumbernauld, Scotland G68 0LL Phone: +44
1236 730 595 Fax: [phone]
Pulse Engineering
Dunmore Road
Tuam Co. Galway, Ireland Phone: [phone] Fax: +353
93 24 459
ΔT
J
= P
D
× (θ
Customer
T
J
JC
= ΔT
+ θ
Interface
J
+ T
A
Response
+ θ
Heat Sink
)
www.national.com
Center