T-55382GD050JU-LW-A-ABN Optrex America Inc, T-55382GD050JU-LW-A-ABN Datasheet - Page 21

• Manufacturer Part Number: T-55382GD050JU-LW-A-ABN
• Description: LCD 5.0" TFT 800X480 WVGA WH LED
• Manufacturer: Optrex America Inc

Specifications of T-55382GD050JU-LW-A-ABN

• Interface: CMOS
• Display Type: TFT- Thin Film Transistor
• Display Mode: Transmissive
• Dot Pixels: 800 x 480
• Attached Touch Screen: Yes
• Background Color: White
• Operating Temperature Range: - 20 C to + 70 C
• Viewing Area (w X H): 108 mm x 64.8 mm
• Pixel Density: 800 x 480
• Module Size (w X H X T): 118.5 mm x 77.8 mm x 3.5 mm
• Backlighting: Edge LED
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Backlight: -
• Viewing Area: -
• Dot Size: -
• Dot Pitch: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 73-1336

(6) OTHERS
(3) PRECAUTIONS WITH ELECTROSTATICS
(4) STORAGE PRECAUTIONS
(5) SAFETY PRECAUTIONS
OPTREX Confidential
c. The interface signal speed is very high. Please pay attention to transmission line design and
d. A condensation might happen on the surface and inside of LCD module in case of sudden change
e. Please pay attention not to display the same pattern for very long time. Image might stick on
f. Please obey the same safe instructions as ones being prepared for ordinary electronic products.
a. This LCD module use CMOS-IC on circuit board and TFT-LCD panel, and so it is easy to be
b. Please remove protection film very slowly from the surface of LCD module to prevent from
a. Please do not leave the LCDs in the environment of high humidity and high temperature such as
b. Please do not leave the LCDs in the environment of low temperature; below -30°C.
a. When you waste damaged or unnecessary LCDs, it is recommended to crush LCDs into pieces
b. If any liquid leaks out of a damaged glass cell and comes in contact with the hands, wash off
c. Be sure to turn off the power supply when inserting or disconnecting the cable.
d. LED driver should be designed carefully to limit or stop it's function when LED over current is
a. A strong incident light into LCD panel might cause display characteristics changing inferior
b. Please pay attention to a panel side of LCD module not to contact with other materials in
c. For the packaging box, please pay attention to the followings;
other high speed signal precautions to satisfy signal specification.
of ambient temperature.
LCD. Even if image sticking happens, it may disappear as the operation time proceeds.
affected by electrostatics. Please be careful with electrostatics by the way of your body
connecting to the ground and so on.
electrostatics occurrence.
60°C90%RH.
and wash them off with solvents such as acetone and ethanol, which should later be burned.
thoroughly with soap and water.
detected on the LED cable.
because of polarizer film, color filter, and other materials becoming inferior. Please do not
expose LCD module direct sunlight and strong UV rays.
preserving it alone.
(a) Packaging box and inner case for LCD are designed to protect the LCDs from the damage or
(b) Please do not pile them up more than 7 boxes. (They are not designed so.) And please do not
(c) Please handle packaging box with care not to give them sudden shock and vibrations. And
(d) Packaging box and inner case for LCDs are made of cardboard. So please pay attention not
scratching during transportation. Please do not open except picking LCDs up from the box.
turn over.
also please do not throw them up.
to get them wet. (Such like keeping them in high humidity or wet place can occur getting
them wet.)
(21/21)
T-55382GD050JU-LW-A-ABN_02_00