HFCT-5911ATLZ Avago Technologies US Inc., HFCT-5911ATLZ Datasheet - Page 7

• Manufacturer Part Number: HFCT-5911ATLZ
• Description: TXRX SMF LC 1.25GBD 2X5 EXT TEMP
• Manufacturer: Avago Technologies US Inc.

Specifications of HFCT-5911ATLZ

• Data Rate: 1.25Gbps
• Wavelength: 1310nm
• Applications: Ethernet
• Voltage - Supply: 3.1 V ~ 3.5 V
• Connector Type: LC Duplex
• Mounting Type: Through Hole
• Supply Voltage: 3.3V
• Leaded Process Compatible: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 6. Recommended Interface Circuit
Application Information
The Applications Engineering Group at Avago Tech-
nologies is available to assist you with technical under-
standing and design trade-offs associated with these
transceivers. You can contact them through your Avago
Technologies’ sales representative.
The following information is provided to answer some
of the most common questions about the use of the
parts.
Optical Power Budget and Link Penalties
The worst-case Optical Power Budget (OPB) in dB for
a fiber-optic link is determined by the difference be-
tween the minimum transmitter output optical power
(dBm avg) and the lowest receiver sensitivity (dBm avg).
This OPB provides the necessary optical signal range to
establish a working fiber-optic link. The OPB is allocated
for the fiber-optic cable length and the corresponding
link penalties. For proper link performance, all penalties
that affect the link performance must be accounted for
within the link optical power budget.
T

Note:
Note A: CIRCUIT ASSUMES OPEN EMITTER OUTPUT.
Note B: CIRCUIT ASSUMES HIGH IMPENDANCE INTERNAL BIAS @ V
DIS
T
R
X
X
(LVTTL)
C1 = C2 = C3 = 10 nF or 100 nF
TD+, TD- INPUTS ARE INTERNALLY TERMINATED AND AC COUPLED.
RD+, RD- OUTPUTS ARE INTERNALLY BIASED AND AC COUPLED.
10
1
9
2
8
3
7
4
6
5
CC
- 1.3 V.
C2
C1
10 µF
10 µF
The Gigabit Ethernet IEEE 802.3 standard identifies, and
has modeled, the contributions of these OPB penalties
to establish the link length requirements for 62.5/125
µm and 50/125 µm multimode fiber usage. In addition,
single mode fiber with standard 1310 nm Fabry-Perot la-
sers have been modeled and specified. Refer to the IEEE
802.3 standard and its supplemental documents that
develop the model, empirical results and specifications.
Refer to Section 38.11. for specification of offset-launch
mode-conditioning patch cord required for MMF opera-
tion of HFCT-5911ATLZ.
10km Link Support
As well as complying with the LX 5 km standard, the
HFCT-5911ATL specification provides additional margin
allowing for a 10 km Gigabit Ethernet link on a single
mode fiber. This is accomplished by limiting the spectral
width and center wavelength range of the transmitter
while increasing the output optical power and improv-
ing sensitivity. All other LX cable plant recommenda-
tions should be followed.
1 µH
1 µH
Z = 50 W
Z = 50 W
Z = 50 W
Z = 50 W
V
CC
(+3.3 V)
C3
10 µF
130 W
100 W
130 W
TD-
TD+
RD+
RD-
SD
LVTTL
V
CC
V
(+3.3 V)
CC
(+3.3 V)
NOTE A
NOTE B