HFBR-1415Z Avago Technologies US Inc., HFBR-1415Z Datasheet - Page 24

• Manufacturer Part Number: HFBR-1415Z
• Description: XMITTER MINI HP FIB OPT ST PORT
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-1415Z

• Wavelength: 820nm
• Voltage - Forward (vf) Typ: 1.7V
• Current - Dc Forward (if): 60mA
• Voltage - Dc Reverse (vr) (max): 3.8V
• Connector Type: ST
• Data Rate Max: 0.16Gbps
• Supply Voltage: 5V
• Wavelength Typ: 820nm
• Leaded Process Compatible: Yes
• Applications: 100Base-SX Fast Ethernet, Media/Fiber Conversion, Switches, Routers, Hubs
• Product: Transmitter
• Data Rate: 160 MBd
• Diode Capacitance: 55 pF
• Operating Supply Voltage: 7 VDC
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• For Use With Fiber Type: Multimode
• Function: High performance fiber optic communication links for information systems and industrial applications
• Transmission Distance: 2.7 Km
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Capacitance: -
• Spectral Bandwidth: -
• Lead Free Status / Rohs Status: Details
• For Use With: Multimode Glass, Hard Clad Silica
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Dynamic Characteristics
-40 °C to +85 °C; 4.75 V d Supply Voltage d 5.25 V; R
Notes:
1. 2.0 mm from where leads enter case.
2. Typical specifications are for operation at T
3. For 200 μm HCS fibers, typical responsivity will be 6 mV/mW. Other parameters will change as well.
4. Pin #2 should be ac coupled to a load ³ 510 ohm. Load capacitance must be less than 5 pF.
5. Measured with a 3 pole Bessel filter with a 75 MHz, -3 dB bandwidth. Recommended receiver filters for various bandwidths are provided in
6. Overdrive is defined at PWD = 2.5 ns.
7. D is the effective diameter of the detector image on the plane of the fiber face. The numerical value is the product of the actual detector di-
8. Measured with a 10 ns pulse width, 50% duty cycle, at the 50% amplitude point of the waveform.
9. Percent overshoot is defined as:
10. The conversion factor for the rise time to bandwidth is 0.41 since the HFBR-24x6Z has a second order bandwidth limiting characteristic.
Figure 14. Recommended ac Coupled Receiver Circuit. (See AB 78 and AN 1038 for more information.)
24
Parameter
Rise/Fall Time 10% to 90%
Pulse Width Distortion
Overshoot
Bandwidth (Electrical)
Bandwidth - Rise Time Product
CAUTION: The small junction sizes inherent to the design of these components increase the components’ susceptibility to damage
from electrostatic discharge (ESD). It is advised that normal static precautions be taken in handling and assembly of these compo-
nents to prevent damage and/or degradation which may be induced by ESD.
Application Bulletin 78.
ameter and the lens magnification.
(
V
PK
V
−
100%
V
100%
)
x
100%
30 pF
0.1 μF
Symbol
t
PWD
BW
r
, t
f
A
= +25 °C and V
6
2
3 & 7
10 Ω
Min
LOAD
R LOADS
500 Ω MIN.
CC
= 511 :, C
= +5 V dc.
POST
AMP
Typ
3.3
0.4
2
125
0.41
2
LOAD
Max
6.3
2.5
= 5 pF unless otherwise specified
Units
ns
ns
%
Hz • s
MHz
OUTPUT
LOGIC
+5 V
Conditions
P
P
P
t
-3 dB Electrical
Note 10
r
R
R
R
= 1.5 ns
= 100 μW peak
= 150 μW peak
= 5 μW peak,
Reference
Figure 17
Note 8,
Figure 16
Note 9