JC050B Lineage Power, JC050B Datasheet
JC050B
Specifications of JC050B
Available stocks
Related parts for JC050B
JC050B Summary of contents
Page 1
... Description The JC050B, JC075B, JC100B Power Modules are dc-dc converters that operate over an input voltage range of 18 Vdc to 36 Vdc and provide a precisely regulated dc output. The outputs are fully isolated from the inputs, allow- ing versatile polarity configurations and grounding connections. The modules have maximum power ratings from 100 W at typical full-load efficiency of 85% ...
Page 2
... Operating Input Voltage Maximum Input Current ( max JC050B (See Figure 1) JC075B (See Figure 2) JC100B (See Figure 3.) Inrush Transient Input Reflected-ripple Current, Peak-to-peak ( MHz, 12 µH source impedance; see Figure 11.) Input Ripple Rejection (120 Hz) Fusing Considerations CAUTION: This power module is not internally fused. An input line fuse must always be used. ...
Page 3
... Vdc to 36 Vdc Input, 12 Vdc Output 100 W (continued) Device Symbol All All V All All All All All All JC050B JC075B JC100B JC050B I JC075B I JC100B I All = 70 °C) JC050B C JC075B JC100B = 25 °C max All All : O, max All All Min Typ Max V 11.64 — 12.36 O 11.78 — ...
Page 4
... O, clamp Tc March 2008 Typ Max Unit 2,600,000 hr. — 100 (3.5) g (oz.) Min Typ Max Unit 0 — 1.2 V — — 1.0 mA — — — — 50 µA — — — 1 — 110 %V O, nom 13.2 — 16.0 V — 105 — °C Lineage Power ...
Page 5
... March 2008 Characteristic Curves The following figures provide typical characteristics for the JC050B, JC075B, JC100B power modules. The figures are identical for both on/off configurations. 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 INPUT VOLTAGE, V Figure 1. Typical JC050B Input Characteristics at Room Temperature ...
Page 6
... OUTPUT CURRENT, I Figure 5. Typical JC075B Output Characteristics at Room Temperature OUTPUT CURRENT, I Figure 6. Typical JC100B Output Characteristics at Room Temperature (continued (A) O Figure 7. Typical JC050B Converter Efficiency vs. 8-1240 (C). (A) O 8-1241 (C) Figure 8. Typical JC075B Converter Efficiency vs March 2008 0.7 1.4 2.1 2.8 OUTPUT CURRENT, I ...
Page 7
... Figure 9. Typical JC100B Converter Efficiency vs. Output Current at Room Temperature TIME ms/div) Figure 10.Typical Start-Up from Remote On/Off JCxxxB1 Full Load O Lineage Power 18 Vdc to 36 Vdc Input, 12 Vdc Output 100 W Test Configurations TO OSCILLOSCOPE BATTERY Note: Measure input reflected-ripple current with a simulated source inductance (L battery impedance ...
Page 8
... If not using the remote on/off feature, do one of the fol- lowing March 2008 (-) terminal ( 1.2 V. The max- on/off during a logic low is 1 mA. The switch on/off on/off on/off For negative logic, short ON/OFF pin to V For positive logic, leave ON/OFF pin open. Lineage Power ). The on/off generated μA. (-) I ...
Page 9
... CONTACT AND RESISTANCE DISTRIBUTION LOSSES Figure 15. Effective Circuit Configuration for Single-Module Remote-Sense Operation Lineage Power 18 Vdc to 36 Vdc Input, 12 Vdc Output 100 W Output Voltage Set-Point Adjustment (Trim) Output voltage trim allows the user to increase or decrease the output voltage set point of a module. This ...
Page 10
... Heat is removed by conduc- tion, convection,a nd radiation to the surrounding environment. Proper cooling can be verified by mea- suring the case temperature. Peak temperature (Tc) occurs at the position indicated in Figure 20. March 2008 10M 1M 100k 10k CHANGE IN OUTPUT VOLTAGE (Δ%) Voltage Lineage Power 8 10 8-880a ...
Page 11
... Figure 21. Forced Convection Power Derating with 0.0 Figure 22. JC050B Power Dissipation vs 8 °C A (Use Figure 24.): 4.0 m/s (800 ft./min 3.5 m/s (700 ft./min 3.0 m/s (600 ft./min 2.5 m/s (500 ft./min 2.0 m/s (400 ft./min 1.5 m/s (300 ft./min 1.0 m/s (200 ft./min ...
Page 12
... The module used to collect the data in Figure 25 had a thermal-conductive dry pad between the case and the heat sink to minimize contact resistance. The use of Figure 25 is shown in the following example Lineage Power ) divided by the ) ...
Page 13
... Use Figure 25 to determine air velocity for the0.5 inch heat sink. The minimum airflow necessary for the JC100B mod- ule is 1.7 m/s (340 ft./min.). Lineage Power 18 Vdc to 36 Vdc Input, 12 Vdc Output 100 W Custom Heat Sinks (continued) A more detailed model can be used to determine the ...
Page 14
... I 48.26 (1.900) 4.8 48.3 (1.90) (0.19) March 2008 2.06 (0.081) DIA SOLDER-PLATED BRASS, 2 PLACES–(OUTPUT AND +OUTPUT) MOUNTING INSERTS M3 x 0.5 THROUGH, 4 PLACES V (–) O 10.16 (0.400) 17.78 –SEN (0.700) 25.40 (1.000) TRIM 35.56 +SEN (1.400) V (+) O Lineage Power 8-1190 ...
Page 15
... Positive remote on/off logic JC100B JC100B1 March 2008 35.56 (1.400) 25.40 (1.000) 61.0 17.78 (2.40) 10.16 (0.700) MAX (0.400) MOUNTING INSERTS Device Comcode Code JC050B1 107201667 JC075B1 107310005 JC100B1 107201683 JC050B 107361479 JC075B 107477184 JC100B 107309940 Option Suffix — Lineage Power 8-1190 ...
Page 16
... Lineage Power reserves the right to make changes to the produc t(s) or information contained herein without notice. No liability is ass umed as a res ult of their use or applic ation. No rights under any patent acc ompany the sale of any oduct information. ...