VPOL5A-12-SIP CUI Inc, VPOL5A-12-SIP Datasheet - Page 2

• Manufacturer Part Number: VPOL5A-12-SIP
• Description: CONVERTER DC/DC 5.0V OUT 5A SIP
• Manufacturer: CUI Inc
• Series: V-Infinity VPOL5Ar
• Type: Point of Load (POL) Non-Isolatedr

Specifications of VPOL5A-12-SIP

• Output: 0.75 ~ 5V
• Number Of Outputs: 1
• Power (watts): 25W
• Mounting Type: Through Hole
• Voltage - Input: 8.3 ~ 14V
• Package / Case: 5-SIP Module
• 1st Output: 5 VDC @ 5A
• Size / Dimension: 0.90" L x 0.22" W x 0.40" H (22.9mm x 5.6mm x 10.2mm)
• Power (watts) - Rated: 25W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 92%
• Approvals: cUL, UL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• Other names: 102-1289

PART NUMBER: VPOL5A-12-SIP
1. Introduction
This application note describes the features and functions of V-Infinity’s
VPOL5A-12-SIP series of non-isolated dc-dc converters. These are
highly efficient, reliable and compact, high power density, single output
DC/DC converters. These “Point of Load” modules serve the needs
specifically of the fixed and mobile telecommunications and computing
market, employing economical distributed Power Architectures. The
VPOL5A-12-SIP series provide precisely regulated output voltage range
from 0.75V to 5.0Vdc over a wide range of input voltage (Vi=8.3 –
14Vdc) and can operate over an ambient temperature range of –40°C
to +85°C. Ultr a-high efficiency operation is achieved through the use of
synchronous rectification and drive control techniques.
The modules are fully protected against short circuit and over-
temperature conditions. V-Infinity’s world class automated
manufacturing methods, together with an extensive testing and
qualification program, ensure that all VPOL5A-12-SIP series converters
are extremely reliable.
2. VPOL5A-12-SIP Converter Features
3. General Description
3.1 Electrical Description
A block diagram of the VPOL5A-12-SIP Series converter is shown in
Figure 1. Extremely high efficiency power conversion is achieved
through the use of synchronous rectification and drive techniques.
Essentially, the powerful VPOL5A-12-SIP series topology is based on a
non-isolated synchronous buck converter. The control loop is optimized
for unconditional stability, fast transient response and a very tight line
and load regulation. In a typical pre-bias application the VPOL5A-12-
SIP series converters do not draw any reverse current at start-up. The
output voltage can be adjusted from 0.75 to 5.0vdc, using the TRIM pin
with a external resistor. The converter can be shut down via a remote
ON/OFF input that is referenced to ground. This input is compatible with
popular logic devices; a 'positive' logic input is supplied as standard.
Positive logic implies that the converter is enabled if the remote
ON/OFF input is high (or floating), and disabled if it is low. The
converter is also protected against over-temperature conditions.
5.0Vdc
High efficiency topology, typically 89% at 3.3Vdc
Industry standard footprint
Wide ambient temperature range, -40°C t o +85°C
Cost efficient open frame design
Programmable output voltage via external resistor from 0.75 to
No minimum load requirement (Stable at all loads)
Remote ON/OFF
Fixed switching frequency
Continuous short-circuit protection and over current protection
Over-temperature protection (OTP)
Monotonic Startup with pre-bias at the output.
UL/IEC/EN60950 Certified.
20050 SW 112
th
Ave. Tualatin, Oregon 97062
phone [phone] fax [phone]
DESCRIPTION: point of load converter
high, the converter will shut down to protect the unit.
3.2 Thermal Packaging and Physical Design.
The VPOL5A-12-SIP series uses a multi-layer FR4 PCB construction.
All surface mount power components are placed on one side of the
PCB, and all low-power control components are placed on the other
side. Thus, the Heat dissipation of the power components is optimized,
ensuring that control components are not thermally stressed. The
converter is an open-frame product and has no case or case pin. The
open-frame design has several advantages over encapsulated closed
devices. Among these advantages are:
If the converter is overloaded or the ambient temperature gets too
+VIN
COM
ON/OFF
C1
heat generating components without heating more sensitive, small
signal control components.
re-cycled.
construction.
offers high reliability and easy diagnostics.
Efficient Thermal Management: the heat is removed from the
Environmental: Lead free open-frame converters are more easily
Cost Efficient: No encapsulation. Cost efficient open-frame
Reliable: Efficient cooling provided by open frame construction
Q1
Figure 1. Electrical Block Diagram
PWM IC
ERR AMP
Q2
D1
L1
C2
rev.
page
date
R1
R2
R trim
08/2007
2 of 12
+VO
COM
TRIM