LTM8022EV#PBF Linear Technology, LTM8022EV#PBF Datasheet - Page 6

• Manufacturer Part Number: LTM8022EV#PBF
• Description: IC DC/DC UMODULE 1A 50-LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM8022EV#PBF

• Design Resources: LTM8022 Spice Model
• Output: 0.8 ~ 10 V
• Number Of Outputs: 1
• Power (watts): 10W
• Mounting Type: Surface Mount
• Voltage - Input: 3.6 ~ 36 V
• Package / Case: 50-LGA
• 1st Output: 0.8 ~ 10 VDC @ 1A
• Size / Dimension: 0.44" L x 0.35" W x 0.11" H (11.25mm x 9mm x 2.82mm)
• Power (watts) - Rated: 10W
• Operating Temperature: -40°C ~ 85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -

PIN FUNCTIONS
LTM8022
V
internal regulator and to the internal power switch. This
pin must be locally bypassed with an external, low ESR
capacitor of at least 2.2μF.
V
capacitor and the output load between these pins and
GND pins.
AUX (Pin F5): Low current voltage source for BIAS. In
many designs, the BIAS pin is simply connected to V
The AUX pin is internally connected to V
adjacent to the BIAS pin to ease printed circuit board
routing. Although this pin is internally connected to V
do NOT connect this pin to the load. If this pin is not tied
to BIAS, leave it fl oating. The Application Information
section gives specifi c information about the BIAS and
AUX connections
BIAS (Pin G5): The BIAS pin connects to the internal power
bus. Connect to a power source greater than 2.4V. If the
output is greater than 2.4V, connect this pin there. If the
output voltage is less, connect this to a voltage source
between 2.4V and 16V. Also, make sure that BIAS + V
is less than 56V.
RUN/SS (Pin H5): Tie RUN/SS pin to ground to shut down
the LTM8022. Tie to 2.5V or more for normal operation.
If the shutdown feature is not used, tie this pin to the V
pin. RUN/SS also provides a soft-start function; see the
Applications Information section.
GND (Bank 3): Tie these GND pins to a local ground plane
below the LTM8022 and the circuit components. Return
the feedback divider (R
6
IN
OUT
(Bank 1): The V
(Bank 2): Power Output Pins. Apply the output fi lter
IN
pin supplies current to the LTM8022’s
ADJ
) to this pin.
OUT
and is placed
OUT
OUT
IN
IN
.
,
R
frequency of the LTM8022 by connecting a resistor from
this pin to ground. The Applications Information section of
the data sheet includes a table to determine the resistance
value based on the desired switching frequency. Minimize
capacitance at this pin.
SHARE (Pin F7): Tie this to the SHARE pin of another
LTM8022 when paralleling the outputs. Otherwise, leave
this pin fl oating.
SYNC (Pin G6): External Clock Synchronization Input.
Ground this pin for low ripple Burst Mode
low output loads, or connect to a stable voltage source
above 0.7V to disable Burst Mode operation. Do not leave
this pin fl oating. Tie to a clock source for synchronization.
Clock edges should have rise and fall times faster than
1μs. See Synchronization in the Applications Information
section.
PG (Pin H6): Open Collector Output of an Internal
Comparator. PG remains low until the ADJ pin is within
10% of the fi nal regulation voltage. PG output is valid when
V
not used, leave this pin fl oating.
ADJ (Pin H7): The LTM8022 regulates its ADJ pin to 0.79V.
Connect the adjust resistor from this pin to ground. The
value of R
(V
T
IN
OUT
(Pin G7): The R
is above 3.6V and RUN/SS is high. If this function is
– 0.79), where R
ADJ
is given by the equation, R
T
pin is used to program the switching
ADJ
is in kΩ.
ADJ
®
operation at
= 394.21/
8022fd