LTM8023IV#PBF Linear Technology, LTM8023IV#PBF Datasheet - Page 12

IC BUCK SYNC ADJ 2A 50LGA

LTM8023IV#PBF

Manufacturer Part Number
LTM8023IV#PBF
Description
IC BUCK SYNC ADJ 2A 50LGA
Manufacturer
Linear Technology
Series
µModuler
Type
Point of Load (POL) Non-Isolatedr
Datasheet

Specifications of LTM8023IV#PBF

Design Resources
LTM8023 Spice Model
Output
0.8 ~ 10 V
Number Of Outputs
1
Power (watts)
20W
Mounting Type
Surface Mount
Voltage - Input
3.6 ~ 36 V
Package / Case
50-LGA
1st Output
0.8 ~ 10 VDC @ 2A
Size / Dimension
0.44" L x 0.35" W x 0.11" H (11.25mm x 9mm x 2.82mm)
Power (watts) - Rated
20W
Operating Temperature
-40°C ~ 85°C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTM8023IV#PBFLTM8023IV
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTM8023IV#PBF
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
LTM8023IV#PBF
0
Company:
Part Number:
LTM8023IV#PBFLTM8023IVDC#PBF
Manufacturer:
LT
Quantity:
218
APPLICATIONS INFORMATION
LTM8023
the peak start-up current can be reduced to the current
that is required to regulate the output, with no overshoot.
Choose the value of the resistor so that it can supply at
least 20μA when the RUN/SS pin reaches 2.5V.
Synchronization
The internal oscillator of the LTM8023 can be synchronized
by applying an external 250kHz to 2MHz clock to the SYNC
pin. Do not leave this pin fl oating . The resistor tied from the
R
oscillates 20% lower than the intended synchronization
frequency (see the Frequency Selection section).
The LTM8023 will not enter Burst Mode operation while
synchronized to an external clock, but will instead skip
pulses to maintain regulation.
Shorted Input Protection
Care needs to be taken in systems where the output will be
held high when the input to the LTM8023 is absent. This
may occur in battery charging applications or in battery
backup systems where a battery or some other supply is
diode OR-ed with the LTM8023’s output. If the V
allowed to fl oat and the SHDN pin is held high (either by a
logic signal or because it is tied to V
internal circuitry will pull its quiescent current through
its internal power switch. This is fi ne if your system can
tolerate a few milliamps in this state. If you ground the
SHDN pin, the internal power switch current will drop to
essentially zero. However, if the V
the output is held high, then parasitic diodes inside the
LTM8023 can pull large currents from the output through
the V
the input voltage is present and that protects against a
shorted or reversed input.
PCB Layout
Most of the headaches associated with PCB layout have
been alleviated or even eliminated by the high level of
integration of the LTM8023. The LTM8023 is neverthe-
less a switching power supply, and care must be taken to
minimize EMI and ensure proper operation. Even with the
12
T
pin to ground should be chosen such that the LTM8023
IN
pin. Figure 4 shows a circuit that will run only when
IN
IN
pin is grounded while
), then the LTM8023’s
IN
pin is
high level of integration, you may fail to achieve specifi ed
operation with a haphazard or poor layout. See Figure 5
for a suggested layout.
Ensure that the grounding and heatsinking are acceptable.
A few rules to keep in mind are:
1. Place the R
2. Place the C
3. Place the C
Figure 4. The Input Diode Prevents a Shorted Input from
Discharging a Backup Battery Tied to the Output. It Also Protects
the Circuit from a Reversed Input. The LTM8023 Runs Only When
the Input is Present.
Figure 5. Layout Showing Suggested External Components, GND
Plane and Thermal Vias
V
their respective pins.
and GND connection of the LTM8023.
V
IN
OUT
GND
and GND connection of the LTM8023.
V
OUT
ADJ
IN
OUT
capacitor as close as possible to the V
and R
capacitor as close as possible to the
C
OUT
V
RUN/SS
T
R
IN
T
resistors as close as possible to
SYNC
LTM8023
SHARE
GND
AUX
C
R
IN
T
BIAS
V
BIAS
AUX
8023 F04
ADJ
OUT
R
V
ADJ
IN
SYNC
PGOOD
RUN/SS
8023 F05
V
OUT
8023ff
IN

Related parts for LTM8023IV#PBF