SXT6A-3-5SA-P Bourns Inc., SXT6A-3-5SA-P Datasheet
SXT6A-3-5SA-P
Specifications of SXT6A-3-5SA-P
Related parts for SXT6A-3-5SA-P
SXT6A-3-5SA-P Summary of contents
Page 1
... Description Bourns ® SXT6A-3-5SA is a non-isolated DC-DC converter offering designers a cost and space-efficient solution with standard features such as remote on/off, precisely regulated programmable output voltage, overcurrent and over-temperature protection, and optional output voltage sequencing. These modules deliver output current with full load efficiency 3.3 V output ...
Page 2
... SXT6A-3-5SA SIP Non-Isolated Power Module Electrical Specifications (Continued) Characteristic Output Voltage Setpoint Accuracy Output Voltage Tolerance Voltage Adjustment Range Line Regulation Load Regulation Temperature Regulation Output Current Output Current Limit Inception (Hiccup Mode) Output Short Circuit Current Output Ripple and Noise Voltage ...
Page 3
... SXT6A-3-5SA SIP Non-Isolated Power Module Feature Specifications Characteristic Remote Enable Open = On (Logic Low) Low = Off (Logic High) Turn-On Delay and Rise Times Case 1: On/Off Low – Applied Case Applied, then On/Off Set Low Case 3: Output Voltage Rise Sequencing Delay Time Tracking Accuracy ...
Page 4
... SXT6A-3-5SA SIP Non-Isolated Power Module Characteristic Curves The curves provided below are typical characteristics for the SXT6A-3-5SA modules at 25 °C. For any specific test configurations or any specific test requests, please contact Bourns. 100.0 95.0 90.0 85.0 80.0 75.0 70.0 1.0 2.0 3 ...
Page 5
... SXT6A-3-5SA SIP Non-Isolated Power Module Characteristic Curves (Continued) 5.0 4.0 3.0 2.0 1.0 0.0 -0.5 1.5 Input Voltage (V ) Fig. 7 Input Voltage vs. I and 3 6 Load: 20 mVolt 2.5 µs Half Load: 20 mVolt 2.5 µs Full Load: 20 mVolt 2.5 µs Time (2.5 µs/div) Fig ...
Page 6
... SXT6A-3-5SA SIP Non-Isolated Power Module Characteristic Curves (Continued) Output Voltage: 50 mVolt 10 µs Output Current (1.8 A/Div): 2 Volt 10 µs Time (10 µs/div) Fig. 13 Transient Response - Step = 3x100 µF Polymer Capacitors 3 ext Output Voltage: 500 mVolt 1 ms On/Off Voltage: 2 Volt 1 ms Time (1 ms/div) Fig. 14 Typical Start-up using Remote On/Off ( ...
Page 7
... SXT6A-3-5SA SIP Non-Isolated Power Module Characteristic Curves (Continued LFM 100 LFM 3 200 LFM Ambient Temperature (°C) Fig. 19 Derating Output Current vs. Local Ambient Temp. and Airflow ( LFM 4 100 LFM 200 LFM Ambient Temperature (°C) Fig. 20 Derating Output Current vs. Local Ambient Temp. and Airflow ( ...
Page 8
... To turn the device OFF, increase the voltage level on the On/Off pin above 2 shown in Figure 23, placing the part into low dissipation sleep mode. The SXT6A-3-5SA-P comes with Active HIGH Positive On/Off logic, i.e., OPEN or HIGH (>2.4 V) will turn on the device. To turn OFF, decrease the voltage level on the On/Off pin below 0.4 V. ...
Page 9
... If left open circuit the output voltage will default to 0.75 Vdc. The correct Rtrim value for a specific voltage can be calculated using the following equation: Rtrim = [21.07/(Vo-0.7525)-5.11] KΩ For example, to set the SXT6A-3-5SA to 3.3 V the following Rtrim resistor must be used: Rtrim = [21.07/(3.3-0.7525)-5.11] KΩ ...
Page 10
... SXT6A-3-5SA SIP Non-Isolated Power Module Operating Information (Continued) Voltage Margining Output voltage margining can be implemented as follows and as shown in Figure 26. 1) Trim-up: Connect a resistor, Rm-up, from the Trim pin to the ground pin for adjusting the voltage upwards, and 2) Trim-down: Connect a resistor, Rm-down, from the Trim pin to the output pin for adjusting the voltage downwards. ...
Page 11
... SXT6A-3-5SA SIP Non-Isolated Power Module Operating Information (Continued) Vo: 1 Volt 500 µs Vseq: 1 Volt 500 µs Time (0.5 ms/div) Fig. 27 Voltage Sequencing at Power Thermal Considerations Sufficient cooling must always be considered to ensure reliable operation, as these devices operate in a variety of thermal environments. ...
Page 12
... SXT6A-3-5SA SIP Non-Isolated Power Module Thermal Considerations (Continued) Air Flow Fig ref1 Temperature Measurement Location Product Dimensions BACK VIEW OF BOARD 25.4 (1.0000) 12.70 (0.5000) 12.32 (0.4850 2.54 (0.100) 2.54 (0.100) 12.7 (0.500) 15.24 (0.600) 17.78 (0.700) 20.32 (0.800 ref1 PINS DIMENSIONS: Die-Tech 315-0969-00 0 ...
Page 13
... SXT6A-3-5SA SIP Non-Isolated Power Module Recommended Hole Pattern COMPONENT SIDE FOOTPRINT 25.4 (1.0000) OUTLINE AREA 6.6 (0.26) 2.54 (0.100) 2.54 (0.100) 12.7 (0.500) 15.24 (0.600) 17.78 (0.700) 20.32 (0.800) Asia-Pacific: Europe: The Americas: Tel: +1-951 781-5500 • Fax: +1-951 781-5700 www.bourns.com REV ...