NH020G Lineage Power, NH020G Datasheet
NH020G
Specifications of NH020G
Available stocks
Related parts for NH020G
NH020G Summary of contents
Page 1
Data Sheet March 28, 2008 RoHS Compliant Applications Distributed Power Architectures n Communication Equipment n Computer Equipment n Options Tight Tolerance output n -40 °C operation n Description The NH020-Series Power SIPs are nonisolated dc-dc converters that operate over an ...
Page 2
... A (see Safety Considerations section). To aid in the proper fuse selection for the given appli- cation, information on inrush energy and maximum dc input current is provided. Refer to the fuse manufacturer’s data for fur- ther information. Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output ...
Page 3
... — — Y — — All — — All — 0 All IO 0 All IO — NH020M h 70 NH020Y h 73 NH020G h 79 NH020F h 84 All — — All — — All — — All — — All — — Min Typ 1,400,000 — ...
Page 4
... Overtemperature Protection (shutdown) Lineage Power 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Device Symbol All Von/off All Ion/off All Von/off All Ion/off All — NH020M Vtrim NH020Y Vtrim NH020G Vtrim NH020F Vtrim All TQ31 NH020-Series Power SIPs: Min Typ Max Unit –0.7 0 µA 6 ...
Page 5
... The following figures provide typical characteristics curves ( °C). Figure 1. Typical Input Characteristics output current. Figure 2. Typical Output Characteristics. Figure 3. Typical Efficiency for NH020M . Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Figure 4. Typical Efficiency for NH020Y. Figure 5. Typical Efficiency for NH020A0G. Figure 6. ...
Page 6
... Figure 7. Typical Output Ripple Voltage fo NH020M (6A Output Current). Figure 8. Typical Output Ripple Voltage for NH020Y (6A Output Current). Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Figure 9. Typical Output Ripple Voltage for NH020F,G (6A Output Current). Figure 10. Typical Transient response to Step load change from 0% to 100% of I0,max at 5V Input ...
Page 7
... I0,max at 5V Input .(Waveform Averaged to remove ripple) Figure 12. Typical start up Transient at 5V input and 6A output. Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Figure 13. Typical start -up Transient with remote on/off at 5V Input and 6A output. ...
Page 8
... V V – I(+) I(-) Lineage Power 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Design Considerations Input Source Impedance The power SIP should be connected to a low ac- impedance input source. Highly inductive source impedances can affect the stability of the SIP. Adding external capacitance close to ...
Page 9
... ELV. The input to these units provided with a maximum 10A normal-blow fuse in the unearthed lead input electrolytic capacitor used, it should be selected using the design information found in the Design Considerations section. Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output ...
Page 10
... GND pin (increase output volt- age). The trim range for the NH020F is +10%, –16%. The trim range for the NH020G is ±10% of VO, nom. The trim range for SIPs that produce less than 2 +20%, –0%. Connecting an external resistor (Rtrim-down) between the TRIM and VO pin decreases the output voltage set point as defined in the following equation ...
Page 11
... Output Voltage Set-Point Adjustment (Trim) (continued) Figure 23. NH020M Rtrim-up Test Results. Figure 24. NH020Y Rtrim-up Test Results. Figure 25. NH020G Rtrim-up Test Results . Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Figure 26. NH020F Rtrim-up Test Results Overcurrent Protection To provide protection in a fault condition, the unit is equipped with internal overcurrent protection ...
Page 12
... Figures 29—32 show typical heat dissipation for the SIP over a range of output currents. Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Figure 29. NH020M Power Dissipation vs. Output current. Figure 30. NH020Y Power Dissipation vs. Output Current. Figure 31. NH020G Power Dissipation vs. Output Current. 12 ...
Page 13
... SIP is assembled in the actual system, the SIP’s temper- ature should be checked as shown in Figure 28 to ensure it does not exceed 115 °C. Layout Considerations Copper paths must not be routed between pins 2 and 3 and pins 7 and 8. Lineage Power 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output NH020-Series Power SIPs: 13 ...
Page 14
... J-STD-001B. These requirements state that solder balls must neither be loose nor violate the power module minimum electrical spacing. The cleanliness designator of the open frame power module is C00 (per J specification). Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output ...
Page 15
... Outline Diagram for Through-Hole Module Dimensions are in millimeters and (inches). Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated] x.xx mm ± 0.25 mm (x.xxx in. ± 0.010 in.) Front View Side View Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output Pin Function 1 VO ...
Page 16
... Data Sheet March 28, 2008 Recommended Hole Pattern Component-side footprint. Dimensions are in millimeters and (inches). Note: No copper should be placed between pins 2 and 3 and pins 7 and 8. Lineage Power NH020-Series Power SIPs: 5 Vdc Input; 1.5 Vdc to 3.3 Vdc Output ...
Page 17
... Optional features can be ordered using the suffixes shown below. The suffixes follow the last letter of the Product Code and are placed in descending alphanumerical order. Table 2. Device Options Option Tight tolerance output (not available on the NH020G) –40 °C operation RoHS Compliant World W ide Headq u arters Lin eag e Po wer Co rp oratio n ...