CDB5524 Cirrus Logic Inc, CDB5524 Datasheet - Page 43

• Manufacturer Part Number: CDB5524
• Description: EVAL BOARD FOR CS5524 ADC
• Manufacturer: Cirrus Logic Inc

Specifications of CDB5524

• Number Of Adc's: 1
• Number Of Bits: 24
• Sampling Rate (per Second): 617
• Data Interface: Serial
• Inputs Per Adc: 4 Differential
• Input Range: 0 ~ 5 V
• Power (typ) @ Conditions: 10.1mW @ 15SPS, 5 V
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: CS5524
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 598-1012

1.8 Power Supply Arrangements
The CS5521/22/23/24/28 A/D converters are de-
signed to operate from a single +5 V analog supply
and a single +5 V or +3 V digital supply. A -2.1 V
supply is usually generated from the charge pump
drive to provide power to the instrumentation am-
plifier’s NBV (negative bias voltage) pin.
Figure 21 illustrates the CS5522 connected with a
+5 V analog supply and with the external compo-
nents required for the charge pump drive. This en-
ables the CS5522 to measure ground-referenced
signals with magnitudes down to ±100 mV.
Figure 22 illustrates the CS5522 connected to mea-
sure ground-referenced unipolar signals of a posi-
tive polarity using the 1 V, 2.5 V, and 5 V ranges
DS317F8
L M 3 3 4
A b s o lu te
C u rre n t
R e fe re n c e
A n a lo g
S u p p ly
+ 5 V
Figure 21. CS5522 Configured to use on-chip charge pump to supply NBV
C o ld J u n c tio n
U p to ± 1 0 0 m V In p u t
+ 5 V
2 .5 V
V -
V +
3 0 1 Ω
R
1 0 k Ω
1 0 k Ω
0 .1 μ F
4 9 9 Ω
B A V 1 9 9
0 .1 μ F
2 0
1 9
1 8
1 7
1 6
3
4
1
6
B A T 8 5
V R E F +
V R E F -
A IN 1 +
A IN 1 -
A G N D
A IN 2 +
A IN 2 -
A 1
A 0
V A +
N B V
2
5
1 N 4 1 4 8
+
on the converter. For the 25 mV, 55 mV, and
100 mV ranges, the signals being digitized must
have a common mode between +1.85 to +2.65 V
(NBV = 0 V).
Although CS5521/22/23/24/28 are optimized for
the measurement of thermocouple outputs, they are
also well suited for the measurement of ratiometric
bridge transducer outputs. Figure 23 illustrates the
CS5522 connected to measure the output of a rati-
ometric differential bridge transducer while operat-
ing from a single +5 V supply. Bridge outputs may
range from 5 mV to 400 mV. See “Digital Gain
Scaling” on page 45 section about manipulating the
gain register to achieve optimum gain scaling.
1 0 μ F
C S5522
1 0 Ω
C P D
7
V D +
1 N 4 1 4 8
0 .033 μ F
X O U T
D G N D
S C L K
S D O
1 4
X IN
S D I
C S
1 3
1 1
10
9
1 5
8
1 2
L o g ic O u tp u ts :
A 0 - A 1 S w itc h fro m
V A + to A G N D .
C h a rg e -p u m p n e tw o rk
fo r V D + = 5 V o n ly a n d
X IN = 3 2 .7 6 8 k H z .
3 2 .7 6 8 ~ 1 0 0 k H z
CS5521/22/23/24/28
In te rfa ce
O p tio n a l
S o u rce
C lo c k
S e ria l
D a ta
0 .1 μ F
43