EVAL-AD5664REBZ Analog Devices Inc, EVAL-AD5664REBZ Datasheet - Page 23

• Manufacturer Part Number: EVAL-AD5664REBZ
• Description: BOARD EVALUATION FOR AD5664R
• Manufacturer: Analog Devices Inc
• Series: nanoDAC™r

Specifications of EVAL-AD5664REBZ

• Number Of Dac's: 4
• Number Of Bits: 16
• Outputs And Type: 4, Single Ended
• Sampling Rate (per Second): 220k
• Data Interface: Serial
• Settling Time: 4µs
• Dac Type: Voltage
• Voltage Supply Source: Single
• Operating Temperature: -40°C ~ 105°C
• Utilized Ic / Part: AD5664R
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

LDAC FUNCTION
The AD5624R/AD5644R/AD5664R DACs have double-
buffered interfaces consisting of two banks of registers: input
registers and DAC registers. The input registers are connected
directly to the input shift register and the digital code is tra
ferred to the relevant input register on completion of a valid
write sequence. The DAC registers contain the digital code u
by the resistor strings.
The double-buffered int
simultaneous updating of all DAC outputs. The user can write
to three of the input registers individually and then write to t
remaining input register, updating all DAC registers simulta-
neously. Command 010 is reserved for this software LDAC.
Access to the DAC registers is
The LDAC register contains two modes of operation for ea
DAC channel. The DAC channels are selected by setting th
bits of the 4-bit LDAC register (DB3, DB2, DB1, a
Command 110 is reserved for setting up the LDAC register.
When the LDAC bit register is set lo
registers are latched and the input register
without affecting the contents of the DAC r
LDAC
be
tra
This is equivalent to
nently low for the se
u
o
d
Table 16. 24-Bit Input Shift Register Contents for LDAC Setu
DB23 to DB22
(MSB)
x
Don’t care
Table 17. 24-Bit Input Shift Register Contents for Internal Re
DB23 to DB22
(M
x
Don’t care
pdate mode. See Table 1
peration. See Table 16 fo
uring the LDAC register
com
nsferred to them on th
SB)
e transparent and t
bit register is set hi
DB21
1
lected
havin
DB21
1
erface is useful if the user requires
Command bits
Command bits (C2 to C0)
e falling edge of the 24
4 for the LDAC
he contents of
gh, however, the DAC
r contents of the input s
setup command.
g an LDAC hardware pin tied perma-
DAC channel, that
(C2 to C0)
DB20
1
controlled by the LDAC function.
DB20
1
w, the corresponding DAC
DB19
0
the inp
regi
s can change state
egisters. When the
DB19
1
ster mode of
is, synchronous
ut registers are
th
DB18
x
registers
hift register
nd DB0).
SCLK pulse.
(A2 to A0); don
Address b
DB18
x
DB17
x
ch
ns-
e
Address bits (A2 to A0)
Rev. B | Page 23 of 28
sed
he
p Command for the AD5624R/AD5644R/AD5664R
ference Setup Command
its
’t care
DB17
x
DB16
x
This flexibility is useful in applications where the user wants to
update select channels simultaneously, while the rest of the
channels update synchronously.
Table 14. LDAC Register Mode of Operation
LDAC Bits
(DB3 to DB0)
0
1
INTERN L REF
Th
can be turned on or off by setting a software programmable bit,
DB0, in the control register. Table 15 shows how the state of the
bit corresponds to the mode of operation. Command 111 is
reserved for setting up the internal reference (see Table 8).
Table 16 shows how the state of the bits in the input shift
register corresponds to the mode of operation of the device
during internal reference setup.
Table 15. Reference Setup Register
Internal Reference
Setup Register
(DB0)
0
1
e on-chi eferen
DB15 to DB4
x
Don’t care
DB16
x
A
p r
DB15 to DB1
x
Don’t care
AD5624R/AD5644R/AD5664R
ERENCE SETUP
ce is off at power-up by default. This
DB3
DAC D
LDAC Mode of O
Normal operation (default), DAC register
update is controlled by write command.
The DAC registers are updated after new
data is read in on the falling edge of the
24
Action
Reference off (default)
Reference on
Set bit to 0 or 1 for required mode of
th
operation on respective channel
SCLK puls
DB2
DAC C
DB0 (LSB)
1/0
Reference setup register
e.
peration
DB1
DAC B
DB0 (LSB)
DAC A
reference