NCP3065D2SLDGEVB ON Semiconductor, NCP3065D2SLDGEVB Datasheet - Page 9

• Manufacturer Part Number: NCP3065D2SLDGEVB
• Description: EVAL BOARD FOR NCP3065D2SLDG
• Manufacturer: ON Semiconductor

Specifications of NCP3065D2SLDGEVB

• Design Resources: NCP3065D2SLDGEVB BOM NCP3065D2SLDGEVB Gerber Files NCP3065D2SLDGEVB Schematic
• Current - Output / Channel: 350mA
• Outputs And Type: 1, Non-Isolated
• Voltage - Output: 7 ~ 23 V
• Voltage - Input: 12V
• Utilized Ic / Part: NCP3065
• Core Chip: NCP3065
• Topology: SEPIC
• No. Of Outputs: 1
• Output Current: 1A
• Output Voltage: 23V
• Dimming Control Type: PWM
• Development Tool Type: Hardware - Eval/Demo Board
• Leaded Process Compatible: Yes
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: NCP3065D2SLDG
• Other names: NCP3065D2SLDGEVBOS

of the NCP3065. Two main converter topologies are
demonstrated with actual test data shown below each of the
circuit diagrams.
8. V
9. V
10. The calculated t
The Following Converter Characteristics Must Be Chosen:
less than 10% of the average inductor current I
set by R
converter output current capability.
value since it will directly affect line and load regulation. Capacitor C
electrolytic designed for switching regulator applications.
(See Notes 8, 9, 10)
Figures 16 through 24 show the simplicity and flexibility
V
V
I
DI
f − Maximum output switch frequency.
V
out
out
in
ripple(pp)
SWCE
F
L
I
V
− Output rectifier forward voltage drop. Typical value for 1N5819 Schottky barrier rectifier is 0.4 V.
− Nominal operating input voltage.
pk (Switch)
− Desired output current.
− Desired peak−to−peak inductor ripple current. For maximum output current it is suggested that DI
− Desired output voltage.
ripple(pp)
t on
t off
I
I
L(avg)
out
R
V
SC
t
C
on
− Darlington Switch Collector to Emitter Voltage Drop, refer to Figures 7, 8, 9 and 10.
L
out
SC
T
. If the design goal is to use a minimum inductance value, let DI
− Desired peak−to−peak output ripple voltage. For best performance the ripple voltage should be kept to a low
on
/t
off
must not exceed the minimum guaranteed oscillator charge to discharge ratio.
DI L
V in * V SWCE * V out
V in * V SWCE * V out
V TH
I L(avg) )
I pk (Switch)
Step−Down
V
V out ) V F
f
8 f C O
ref
DI L
t on
t off
0.20
I out
1
L(avg)
R 2
R 1
t on
t off
R
) 1
Figure 16. Design Equations
sense
) 1
DI L
2
. This will help prevent I
2
) (ESR)
http://onsemi.com
APPLICATIONS
C T + 381.6 @ 10
t on
2
9
parameters. Additionally, a complete application design aid
for the NCP3065 can be found at www.onsemi.com.
f osc
Figure 16 gives the relevant design equations for the key
O
*6
should be a low equivalent series resistance (ESR)
pk (Switch)
* 343 @ 10
L
= 2(I
from reaching the current limit threshold
L(avg)
[
*12
V in * V SWCE
t on I out
V out ) V F * V in
). This will proportionally reduce
V in * V SWCE
I out
C O
V TH
I L(avg) )
I pk (Switch)
V
f
Step−Up
ref
DI L
t on
t off
0.20
t on
t off
R 2
R 1
) DI L @ ESR
t on
t off
R
) 1
sense
) 1
) 1
DI L
2
t on
L
be chosen to be