STM8/128-EV/TS STMicroelectronics, STM8/128-EV/TS Datasheet - Page 15

• Manufacturer Part Number: STM8/128-EV/TS
• Description: EVAL KIT TOUCH SENSING STM8S
• Manufacturer: STMicroelectronics
• Series: STM8Sr

Specifications of STM8/128-EV/TS

• Sensor Type: Touch, Capacitive
• Sensing Range: 5 Buttons/Keys, Slider
• Interface: I²C
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: STM8S2xx
• Processor To Be Evaluated: STM8S
• Data Bus Width: 8 bit
• Interface Type: I2C
• Silicon Manufacturer: ST Micro
• Core Architecture: STM8
• Core Sub-architecture: STM8
• Silicon Core Number: STM8
• Silicon Family Name: STM8S2xx
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Voltage - Supply: -
• Sensitivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With: STM8Sxxx-TS1
• Other names: 497-10031

UM0671
4
4.1
4.2
Note:
Advanced evaluation using a debugging environment
Running the evaluation firmware in debug mode
Designers can easily run the evaluation firmware in Debug mode using ST debugging and
programming tools.
In Debug mode, designers can perform an in-depth evaluation of the firmware and visualize
touch sensing parameters. Designers can even customize the touch sensing library to their
specific needs by creating their own application firmware.
For further information about ST software, STM8 microcontrollers or debugging tools,
please read the associated documentation or ask your local ST support team for a training
session. More information is available at www.st.com/touch-sense-sw-lib
Entering debug mode using RLink
This section describes the steps necessary to set up a platform for evaluating and
developing TS firmware.
For links to tools and downloads, please refer to ST’s microcontroller web site at
www.st.com/mcu/.
1.
2.
3.
4.
5.
Hardware tools to be ordered separately:
–
–
Software tools to be downloaded separately:
–
–
Download and install the ST MCU Toolset with ST Visual Develop (STVD) IDE and ST
Visual Programmer (STVP) programming interface (one single download).
Download and install the STM8 cosmic C compiler.
Install the Rlink USB driver using one of the two following methods:
–
–
Restart your computer to apply these changes.
Install the RLink hardware:
a)
b)
c)
d)
e)
Raisonance RLink debugger/programmer for ST microcontrollers
(www.raisonance.com/)
STice in-circuit emulation system
ST MCU Toolset with ST Visual Develop (STVD) IDE and ST Visual Programmer
(STVP) programming interface
STM8 Cosmic C compiler (www.cosmic-software.com/)
Insert the RAISONANCE CD-ROM into your CD drive and exit from Autorun.
Explore the CD-ROM contents and execute the RLinkUSBInstall.exe file in the
D:\Driver\RlinkDrv directory.
Download the RLinkUSBInstall.exe file from the Raisonance web site and execute
the file.
Place jumpers on the “SWIM” and “ADAPT” RLink configuration pins of the Rlink
USB adaptor as shown in
Connect the SWIM-STM8 adaptor to the RLink USB adaptor.
Connect the SWIM cable between the touch sensing daughterboard (J5 SWIM
connector) and the SWIM-STM8 adaptor as shown in
Connect the USB cable between your PC and the RLink USB adaptor.
Power the TS daughterboard through the STM8S2xx evaluation board.
Doc ID 15330 Rev 4
Advanced evaluation using a debugging environment
Figure
8.
Figure
9.
15/23