Z8700000ZEM Zilog, Z8700000ZEM Datasheet - Page 3

• Manufacturer Part Number: Z8700000ZEM
• Description: Z87000 ICEBOX
• Manufacturer: Zilog
• Series: ICEBOX™r
• Type: In-Circuit Emulator Systemr

Specifications of Z8700000ZEM

• Contents: Emulator Board, Cables, Software and Documentation
• For Use With/related Products: Z87000, Z87L01
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

LIMITATIONS (Continued)
7. The ICEBOX breakpoint hardware does not distinguish
© 1995 by Zilog, Inc. All rights reserved. No part of this document
may be copied or reproduced in any form or by any means
without the prior written consent of Zilog, Inc. The information in
this document is subject to change without notice. Devices sold
by Zilog, Inc. are covered by warranty and patent indemnification
provisions appearing in Zilog, Inc. Terms and Conditions of Sale
only. Zilog, Inc. makes no warranty, express, statutory, implied or
by description, regarding the information set forth herein or
regarding the freedom of the described devices from intellectual
property infringement. Zilog, Inc. makes no warranty of mer-
chantability or fitness for any purpose. Zilog, Inc. shall not be
responsible for any errors that may appear in this document.
Zilog, Inc. makes no commitment to update or keep current the
information contained in this document.
between instruction and data fetches. When a
breakpoint in the GUI is set, the breakpoint hardware
triggers when the addresses match for either code or
data fetches.
Example:
000C
000E
0010
0012
0013
0016
Setting the breakpoint at %0016 and click GO.
Result: The code will break and stop at %0012.
Note: This will not happen when Animate Mode is on
because the GUI is not using the hardware breakpoints
when in Animate Mode.
SRP
LD
LD
NOP
J P
NOP
#%0
R4, #%0016
R5, @R4
%000C
PRECAUTION LIST
1. Breakpoint Overshoot. The Disassembly window shows
2. Executing GUI. The GUI will occasionally continue to
3. The emulator cannot be operated while performing
4. GUI software versions prior to 3.00 are incompatible
5. The status color bar in OTP dialog box will be cleared
6. The PLC Z89C00 Assembler RESET symbol in symbol
7. For 386 PCs, set the baud rate to 19.2K or less
Zilog’s products are not authorized for use as critical compo-
nents in life support devices or systems unless a specific written
agreement pertaining to such intended use is executed between
the customer and Zilog prior to use. Life support devices or
systems are those which are intended for surgical implantation
into the body, or which sustains life whose failure to perform,
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result in
significant injury to the user.
Zilog, Inc. 210 East Hacienda Ave.
Campbell, CA 95008-6600
Telephone [phone]
Telex 910-338-7621
FAX [phone]
Internet: http://www.zilog.com
the processor halting at one or two instructions past
the instruction where the breakpoint was set.
indicate executing after it has been told to halt. Pushing
the GO button will then result in executing. (Executing
showing at the top of the screen).
ESD/EMI testing on the target board.
with hardware containing BOOTROM 3.00. The GUI
software may still boot, but will fail at some later point
of the session.
in the area where a new window opens on top of it.
table is fixed at 1000 when the assembly code contains
“VECTOR RESET =” statement.
because the Windows’ communication driver does not
guarantee “reliable” operation at more than 9600
baud. Selecting a high baud rate on some slower 386
machines may crash the Windows environment.
CP95WRL1001
Z8700000ZEM
3