08053D105KAT2A AVX Corporation, 08053D105KAT2A Datasheet - Page 2

• Manufacturer Part Number: 08053D105KAT2A
• Description: CAP CERM 1UF 10% 25V X5R 0805
• Manufacturer: AVX Corporation

Specifications of 08053D105KAT2A

• Capacitance: 1.0µF
• Package / Case: 0805 (2012 Metric)
• Voltage - Rated: 25V
• Tolerance: ±10%
• Temperature Coefficient: X5R
• Mounting Type: Surface Mount, MLCC
• Operating Temperature: -55°C ~ 85°C
• Applications: General Purpose
• Size / Dimension: 0.079" L x 0.049" W (2.00mm x 1.25mm)
• Thickness: 1.40mm Max
• Tolerance (+ Or -): 10%
• Voltage: 25VDC
• Temp Coeff (dielectric): X5R
• Operating Temp Range: -55C to 85C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2.01mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.4mm
• Product Diameter (mm): Not Requiredmm
• Dielectric Characteristic: X5R
• Capacitance Tolerance: ± 10%
• Voltage Rating: 25VDC
• Capacitor Case Style: 0805
• No. Of Pins: 2
• Capacitor Mounting: SMD
• Rohs Compliant: Yes
• Case Size: 0805
• Material, Element: Ceramic
• Termination: SMT
• Voltage, Rating: 25 VDC
• Operating Temperature Range: -55°C To +85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Ratings: -
• Lead Spacing: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: 478-1409-2

X5R Dielectric
Specifications and Test Methods
Resistance to
Resistance to
Operating Temperature Range
Solder Heat
Load Life
Humidity
Stresses
Thermal
Flexure
Shock
Load
Insulation Resistance
Dielectric Strength
Dissipation Factor
Parameter/Test
Capacitance
Solderability
Capacitance
Capacitance
Capacitance
Capacitance
Capacitance
Appearance
Appearance
Appearance
Appearance
Appearance
Resistance
Resistance
Resistance
Resistance
Resistance
Dissipation
Dissipation
Dissipation
Dissipation
Dissipation
Insulation
Insulation
Insulation
Insulation
Insulation
Dielectric
Dielectric
Dielectric
Dielectric
Variation
Variation
Strength
Variation
Strength
Variation
Strength
Variation
Strength
Factor
Factor
Factor
Factor
Factor
No defects, <25% leaching of either end terminal
≥ 95% of each terminal should be covered
≤ 12.5% Max. for 16V DC rating and lower
No breakdown or visual defects
≥ Initial Value x 0.3 (See Above)
≥ Initial Value x 0.3 (See Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
≤ Initial Value x 2.0 (See Above)
Meets Initial Values (As Above)
≤ Initial Value x 2.0 (See Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Contact Factory for DF by PN
X5R Specification Limits
≤ 2.5% for ≥ 50V DC rating
10,000MΩ or 500MΩ - μF,
Within specified tolerance
≤ 3.0% for 25V DC rating
≥ Initial Value x 0.3
No visual defects
whichever is less
with fresh solder
No visual defects
-55ºC to +85ºC
No visual defects
No defects
≤ ±12.5%
≤ ±12.5%
≤ ±12%
≤ ±7.5%
≤ ±7.5%
1-5 seconds, w/charge and discharge current
seconds. Store at room temperature for 24 ± 2
Charge device with 300% of rated voltage for
hours before measuring electrical properties.
Dip device in eutectic solder at 260ºC for 60
Step 1: -55ºC ± 2º
Step 2: Room Temp
Step 3: +85ºC ± 2º
Step 4: Room Temp
Repeat for 5 cycles and measure after
24 ± 2 hours at room temperature
test chamber set at 85ºC ± 2ºC for 1000 hours
Dip device in eutectic solder at 230 ± 5ºC
85% ± 5% relative humidity for 1000 hours
Store in a test chamber set at 85ºC ± 2ºC/
specification part numbers that are tested at
(+48, -0). Note: Contact factory for *optional
Remove from chamber and stabilize at
Charge device with 1.5X rated voltage in
Remove from test chamber and stabilize
120 ± 5 secs @ room temp/humidity
Charge device with rated voltage for
For Cap > 10 μF, 0.5Vrms @ 120Hz
at room temperature for 24 ± 2 hours
(+48, -0) with rated voltage applied.
room temperature and humidity for
24 ± 2 hours before measuring.
Temperature Cycle Chamber
Measuring Conditions
Voltage: 1.0Vrms ± .2V
Test Time: 30 seconds
limited to 50 mA (max)
Freq.: 1.0 kHz ± 10%
for 5.0 ± 0.5 seconds
< 1.5X rated voltage.
before measuring.
Deflection: 2mm
90 mm
1mm/sec
30 ± 3 minutes
≤ 3 minutes
30 ± 3 minutes
≤ 3 minutes
25