PIC12F675-I/P Microchip Technology, PIC12F675-I/P Datasheet - Page 8

• Manufacturer Part Number: PIC12F675-I/P
• Description: IC MCU CMOS FLASH-BASE 8BIT 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F675-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 53270-913
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163029 - BOARD PICDEM FOR MECHATRONICSAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12F629/675/PIC16F630/676
2.3.1.5
After receiving this command, the chip will transmit data
bits out of the data memory starting with the second
rising edge of the clock input. The data pin will go into
Output mode on the second rising edge and revert to
Input mode (high-impedance) after the 16th rising edge.
As previously stated, the data memory is 8 bits wide and
therefore, only the first 8 bits that are output are actual
data. If the data memory is code-protected, the data is
read as all zeros. A timing diagram of this command is
shown in Figure 2-7.
FIGURE 2-7:
2.3.1.6
The PC is incremented when this command is
received. A timing diagram of this command is shown
in Figure 2-8.
It is not possible to decrement the address counter. To
reset this counter, the user should exit and re-enter
Programming mode.
FIGURE 2-8:
DS41191D-page 8
CLOCK
GP0
GP1
DATA
CLOCK
GP0
GP1
DATA
Note 1: GP0 and GP1 apply to PIC12F629/675 only. For PIC16F630/676, use RA0 and RA1, respectively.
Note 1: GP0 and GP1 apply to PIC12F629/675 only. For PIC16F630/676, use RA0 and RA1, respectively.
(1)
(1)
(1)
(1)
Read Data From Data Memory
T
Increment Address
SET
1
1
1
READ DATA FROM DATA MEMORY COMMAND
INCREMENT ADDRESS COMMAND (PROGRAM/VERIFY)
2
0
1
0
T
HLD
3
1
1
Input
2
1
4
0
T
3
1
SET
5
x
1
x
6
4
T
0
T
DLY
DLY
2
1
T
strt_bit
1
HLD
5
x
1
2
LSb
x
6
T
DLY
T
3
T
DLY
DLY
3
2
1
4
1
Output
x
© 2005 Microchip Technology Inc.
Next Command
5
2
0
15
MSb
16
Input
stp_bit