ATTINY13A-SSU Atmel, ATTINY13A-SSU Datasheet - Page 106

• Manufacturer Part Number: ATTINY13A-SSU
• Description: IC MCU AVR 1K FLASH 20MHZ 8SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY13A-SSU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 1KB (512 x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: SPI
• Total Internal Ram Size: 64Byte
• # I/os (max): 6
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 4-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC
• Package: 8SOIC
• Family Name: ATtiny
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 2.5|3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 6
• Number Of Timers: 1
• Processor Series: ATTINY1x
• Core: AVR8
• Data Ram Size: 64 B
• Maximum Clock Frequency: 20 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAKSTK511
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / Rohs Status: Compliant

17.6
106
Serial Programming
ATtiny13A
Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while
RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and MISO (out-
put). See
Figure 17-1. Serial Programming and Verify
Note:
After RESET is set low, the Programming Enable instruction needs to be executed first before
program/erase operations can be executed.
Table 17-7.
Note:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
If clocked by internal oscillator there is no need to connect a clock source to the CLKI pin.
In
dedicated for the internal SPI interface.
Symbol
MOSI
MISO
Figure
SCK
Table 17-7
RESET
Pin Mapping Serial Programming
17-1.
above, the pin mapping for SPI programming is listed. Not all parts use the SPI pins
ck
ck
Pins
PB0
PB1
PB2
< 12 MHz, 3 CPU clock cycles for f
< 12 MHz, 3 CPU clock cycles for f
PB5
GND
VCC
PB2
PB1
PB0
I/O
O
I
I
+1.8 - 5.5V
ck
ck
>= 12 MHz
>= 12 MHz
Description
Serial Data in
Serial Data out
Serial Clock
SCK
MISO
MOSI
8126E–AVR–07/10