AT89S51-24PU Atmel, AT89S51-24PU Datasheet - Page 20

• Manufacturer Part Number: AT89S51-24PU
• Description: IC MCU 4K FLASH 24MHZ 40-DIP
• Manufacturer: Atmel
• Series: 89Sr

Specifications of AT89S51-24PU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 24MHz
• Connectivity: UART/USART
• Peripherals: WDT
• Number Of I /o: 32
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: ISP/UART
• Maximum Clock Frequency: 24 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 2
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• Controller Family/series: (8051) 8052
• No. Of I/o's: 32
• Ram Memory Size: 128Byte
• Cpu Speed: 24MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

20. Serial Programming Instruction Set
Note:
After Reset signal is high, SCK should be low for at least 64 system clocks before it goes high to clock in the enable data
bytes. No pulsing of Reset signal is necessary. SCK should be no faster than 1/16 of the system clock at XTAL1.
For Page Read/Write, the data always starts from byte 0 to 255. After the command byte and upper address byte are
latched, each byte thereafter is treated as data until all 256 bytes are shifted in/out. Then the next instruction will be ready
to be decoded.
20
Instruction
Programming Enable
Chip Erase
Read Program Memory
(Byte Mode)
Write Program Memory
(Byte Mode)
Write Lock Bits
Read Lock Bits
Read Signature Bytes
Read Program Memory
(Page Mode)
Write Program Memory
(Page Mode)
1. B1 = 0, B2 = 0
B1 = 0, B2 = 1
B1 = 1, B2 = 0
B1 = 1, B2 = 1
(1)
AT89S51
→
→
→
→
Byte 1
1010 1100
1010 1100
0010 0000
0100 0000
1010 1100
0010 0100
0010 1000
0011 0000
0101 0000
Mode 1, no lock protection
Mode 2, lock bit 1 activated
Mode 3, lock bit 2 activated
Mode 4, lock bit 3 activated
Byte 2
0101 0011
100x xxxx
xxxx
xxxx
1110 00
xxxx xxxx
xxxx
xxxx
xxxx
Instruction Format
}
Byte 3
xxxx xxxx
xxxx xxxx
xxxx xxxx
xxxx xxxx
Byte 0
Byte 0
xxx xxx0
Each of the lock bit modes need to be activated sequentially be-
fore Mode 4 can be executed.
Byte 4
xxxx xxxx
0110 1001
(Output on
MISO)
xxxx xxxx
xxxx xxxx
xxx
Signature Byte
Byte 1...
Byte 255
Byte 1...
Byte 255
xx
Write Lock bits. See Note (1).
Operation
Enable Serial Programming
while RST is high
Chip Erase Flash memory
array
Read data from Program
memory in the byte mode
Write data to Program
memory in the byte mode
Read back current status of
the lock bits (a programmed
lock bit reads back as a “1”)
Read Signature Byte
Read data from Program
memory in the Page Mode
(256 bytes)
Write data to Program
memory in the Page Mode
(256 bytes)
2487C–MICRO–03/05