ATTINY25V-10PU Atmel, ATTINY25V-10PU Datasheet - Page 98

• Manufacturer Part Number: ATTINY25V-10PU
• Description: IC AVR MCU 2K 10MHZ 8-DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY25V-10PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 10MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Processor Series: ATTINY2x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: USI
• Maximum Clock Frequency: 10 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Controller Family/series: AVR Tiny
• No. Of I/o's: 6
• Eeprom Memory Size: 128Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 10MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIPATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13. 8-bit Timer/Counter1 in ATtiny15 Mode
13.1
13.2
98
Timer/Counter1 Prescaler
Counter and Compare Units
ATtiny25/45/85
The ATtiny15 compatibility mode is selected by writing the code “0011” to the CKSEL fuses (if
any other code is written, the Timer/Counter1 is working in normal mode). When selected the
ATtiny15 compatibility mode provides an ATtiny15 backward compatible prescaler and
Timer/Counter. Furthermore, the clocking system has same clock frequencies as in ATtiny15.
Figure 13-1
caler for the system clock (CK) and a 3-bit prescaler for the fast peripheral clock (PCK). The
clocking system of the Timer/Counter1 is always synchronous in the ATtiny15 compatibility
mode, because the same RC Oscillator is used as a PLL clock source (generates the input clock
for the prescaler) and the AVR core.
Figure 13-1. Timer/Counter1 Prescaler
The same clock selections as in ATtiny15 can be chosen for Timer/Counter1 from the output
multiplexer, because the frequency of the fast peripheral clock is 25.6 MHz and the prescaler is
similar in the ATtiny15 compatibility mode. The clock selections are PCK, PCK/2, PCK/4, PCK/8,
CK, CK/2, CK/4, CK/8, CK/16, CK/32, CK/64, CK/128, CK/256, CK/512, CK/1024 and stop.
Figure 13-2
delays in between registers. Note that all clock gating details are not shown in the figure. The
Timer/Counter1 register values go through the internal synchronization registers, which cause
the input synchronization delay, before affecting the counter operation. The registers TCCR1,
GTCCR, OCR1A and OCR1C can be read back right after writing the register. The read back
values are delayed for the Timer/Counter1 (TCNT1) register and flags (OCF1A and TOV1),
because of the input and output synchronization.
The Timer/Counter1 features a high resolution and a high accuracy usage with the lower pres-
caling opportunities. It can also support an accurate, high speed, 8-bit Pulse Width Modulator
(PWM) using clock speeds up to 25.6 MHz. In this mode, Timer/Counter1 and the Output Com-
pare Registers serve as a stand-alone PWM. Refer to
PSR1
CK (1.6 MHz)
PCK (25.6 MHz)
CS10
CS11
CS12
CS13
shows Timer/Counter 1 synchronization register block diagram and synchronization
shows an ATtiny15 compatible prescaler. It has two prescaler units, a 10-bit pres-
CLEAR
3-BIT T/C PRESCALER
0
TIMER/COUNTER1 COUNT ENABLE
“Timer/Counter1 in PWM Mode” on page
CLEAR
10-BIT T/C PRESCALER
2586M–AVR–07/10