PIC16F785-I/SS Microchip Technology, PIC16F785-I/SS Datasheet - Page 6

• Manufacturer Part Number: PIC16F785-I/SS
• Description: IC PIC MCU FLASH 2KX14 20SSOP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F785-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 20-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SS1-1 - SOCKET TRANSITION 20DIP 20SSOPXLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC162060 - HEADER INTRFC MPLAB ICD2 20PINAC164307 - MODULE SKT FOR PM3 28SSOP
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F785/HV785
3.0
Two methods are available to enter Program/Verify
mode. The ‘V
ICSPDAT and ICSPCLK low while raising MCLR pin
from V
data. This method can be used for any Configuration
Word selection and must be used if the INTOSC and
internal MCLR options are selected (FOSC<2:0> = 100
or 101 and MCLRE = 0). The V
the device from executing code prior to entering
Program/Verify mode. See the timing diagram in
Figure 3-1. To prevent the device from executing code
while exiting Program/Verify mode, the ‘V
also be used if the INTOSC and internal MCLR options
are selected. See the timing diagram in Figure 3-3.
The second entry method, ‘V
applying V
then raising MCLR pin from V
followed by data. This method can be used for any
Configuration Word selection except when INTOSC
and
(FOSC<2:0> = 100 or 101 and MCLRE = 0). This
technique is useful when programming the device
when V
disconnect V
See the timing diagram in Figure 3-2.
Once in this mode, the program memory, data memory,
and configuration memory can be accessed and
programmed in serial fashion. ICSPDAT and ICSPCLK
are Schmitt Trigger inputs in this mode.
The sequence that enters the device into the
Programming/Verify mode momentarily places all other
logic into the Reset state (the MCLR pin was initially at
V
impedance inputs) and the Program Counter (PC) is
cleared.
To prevent a device configured with INTOSC and
internal MCLR from executing after exiting Program/
Verify mode, V
See Figure 3-3 for the timing.
DS41237D-page 6
IL
). Therefore, all I/O’s are in the Reset state (high-
IL
internal
DD
to V
PROGRAM/VERIFY MODE
is already applied, for it is not necessary to
DD
IHH
DD
, holding ICSPDAT and ICSPCLK low,
PP
DD
to enter or exit Program/Verify mode.
(high voltage), then applying V
-first’ method is entered by holding
MCLR
needs to power-down before V
options
IL
DD
to V
PP
-first’, is entered by
-first entry prevents
IHH
are
(high voltage),
PP
-last’ must
selected
DD
and
PP
.
FIGURE 3-1:
FIGURE 3-2:
FIGURE 3-3:
ICSPDAT
ICSPCLK
ICSPCLK
Note:
ICSPDAT
Note:
Note:
ICSPDAT
ICSPCLK
V
V
V
V
V
V
DD
PP
DD
PP
DD
PP
This method of entry is not valid if
INTOSC and internal MCLR are selected.
This method must be used if INTOSC
and internal MCLR are selected.
This method of entry is valid, regardless
of Configuration Word selected.
T
T
V
VERIFY MODE ENTRY
V
VERIFY MODE ENTRY
V
VERIFY MODE EXIT
PPDP
HLD
 2009 Microchip Technology Inc.
PP
DD
PP
T
HLD
0
-FIRST PROGRAM/
-LAST PROGRAM/
-FIRST PROGRAM/
0
T
T
HLD
PPDP
0