ATTINY85-20PU Atmel, ATTINY85-20PU Datasheet - Page 148

• Manufacturer Part Number: ATTINY85-20PU
• Description: IC AVR MCU 8K 20MHZ 8DIP
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY85-20PU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 6
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Processor Series: ATTINY8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: USI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Controller Family/series: AVR Tiny
• No. Of I/o's: 6
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 20MHz
• No. Of Timers: 2
• Rohs Compliant: Yes
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Total Internal Ram Size: 512Byte
• # I/os (max): 6
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 8
• Package Type: PDIP
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATAVRBC100 - REF DESIGN KIT BATTERY CHARGER770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.6.3
148
ATtiny25/45/85
Reading Device Signature Imprint Table from Firmware
To read the Fuse High Byte (FHB), simply replace the address in the Z-pointer with 0x0003 and
repeat the procedure above. If successful, the contents of the destination register are as follows.
Refer to
To read the Fuse Extended Byte (FEB), replace the address in the Z-pointer with 0x0002 and
repeat the previous procedure. If successful, the contents of the destination register are as
follows.
Refer to
Byte.
To read the contents of the device signature imprint table, follow the below procedure:
See program example below.
Note:
If successful, the contents of the destination register are as described in section
ture Imprint Table” on page
Bit
Rd
Bit
Rd
Assembly Code Example
1. Load the Z-pointer with the table index.
2. Set RSIG and SPMEN bits in SPMCSR.
3. Issue an LPM instruction within three clock cycles.
4. Read table data from the LPM destination register.
DSIT_read:
; Uses Z-pointer as table index
ldi
ldi
; Preload SPMCSR bits into R16, then write to SPMCSR
ldi
out SPMCSR, r16
; Issue LPM. Table data will be returned into r17
lpm r17, Z
ret
1. See
Table 20-4 on page 152
Table 20-3 on page 152
ZH, 0
ZL, 1
r16, (1<<RSIG)|(1<<SPMEN)
“Code Examples” on page
FHB7
FEB7
7
7
FHB6
FEB6
(1)
6
6
153.
for detailed description and mapping of the Fuse High Byte.
FHB5
FEB5
for detailed description and mapping of the Fuse Extended
5
5
6.
FHB4
FEB4
4
4
FHB3
FEB3
3
3
FHB2
FEB2
2
2
FHB1
FEB1
1
1
FHB0
FEB0
“Device Signa-
0
0
2586M–AVR–07/10