PIC18F23K20-I/SP Microchip Technology, PIC18F23K20-I/SP Datasheet - Page 184

• Manufacturer Part Number: PIC18F23K20-I/SP
• Description: IC PIC MCU FLASH 4KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F23K20-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: CCP/ECCP/EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F2XK20/4XK20
FIGURE 16-10:
16.4.5
The Enhanced PWM can be configured to automati-
cally restart the PWM signal once the auto-shutdown
condition has been removed. Auto-restart is enabled by
setting the PRSEN bit in the PWM1CON register.
If auto-restart is enabled, the ECCPASE bit will remain
set as long as the auto-shutdown condition is active.
When the auto-shutdown condition is removed, the
ECCPASE bit will be cleared via hardware and normal
operation will resume.
FIGURE 16-11:
DS41303G-page 184
Note 1: The
Shutdown
Shutdown
2: Writing to the ECCPASE bit is disabled
3: Once the auto-shutdown condition has
ECCPASE bit
PWM
ECCPASE bit
PWM
AUTO-RESTART MODE
level-based signal, not an edge-based
signal. As long as the level is present, the
auto-shutdown will persist.
while
persists.
been removed and the PWM restarted
(either through firmware or auto-restart)
the PWM signal will always restart at the
beginning of the next PWM period.
Activity
Activity
Event
Event
auto-shutdown
an
PWM Period
PWM Period
PWM AUTO-SHUTDOWN WITH FIRMWARE RESTART (PRSEN = 0)
PWM AUTO-SHUTDOWN WITH AUTO-RESTART ENABLED (PRSEN = 1)
Start of
Start of
auto-shutdown
condition
Normal PWM
Normal PWM
condition
is
a
Event Occurs
Event Occurs
PWM Period
PWM Period
Shutdown
Shutdown
Event Clears
Event Clears
Shutdown
Shutdown
Cleared by
ECCPASE
Firmware
 2010 Microchip Technology Inc.
Resumes
Resumes
PWM
PWM