PIC18F14K50-I/SS Microchip Technology, PIC18F14K50-I/SS Datasheet - Page 89

• Manufacturer Part Number: PIC18F14K50-I/SS
• Description: IC PIC MCU FLASH 8KX16 20-SSOP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F14K50-I/SS

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 20-SSOP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 14
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 768 B
• Interface Type: EUSART, I2C, MSSP, SPI, USB
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 15
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Package: 20SSOP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC244023 - PROC EXTENS PAK PIC18F1XK50DV164126 - KIT DEVELOPMENT USB W/PICKIT 2DM164127 - KIT DEVELOPMENT USB 18F14/13K50AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPXLT20SS-1 - SOCKET TRANSITION 18DIP 20SSOPAC164307 - MODULE SKT FOR PM3 28SSOP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9.2
PORTB is an 4-bit wide, bidirectional port. The corre-
sponding data direction register is TRISB. Setting a
TRISB bit (= 1) will make the corresponding PORTB
pin an input (i.e., disable the output driver). Clearing a
TRISB bit (= 0) will make the corresponding PORTB
pin an output (i.e., enable the output driver and put the
contents of the output latch on the selected pin).
The PORTB Data Latch register (LATB) is also memory
mapped. Read-modify-write operations on the LATB
register read and write the latched output value for
PORTB.
EXAMPLE 9-2:
All PORTB pins are individually configurable as
interrupt-on-change pins. Control bits in the IOCB reg-
ister enable (when set) or disable (when clear) the
interrupt function for each pin.
When set, the RABIE bit of the INTCON register
enables interrupts on all pins which also have their
corresponding IOCB bit set. When clear, the RABIE
bit disables all interrupt-on-changes.
Only pins configured as inputs can cause this interrupt
to occur (i.e., any pin configured as an output is
excluded from the interrupt-on-change comparison).
For enabled interrupt-on-change pins, the values are
compared with the old value latched on the last read of
PORTB. The ‘mismatch’ outputs of the last read are
OR’d together to set the PORTB Change Interrupt flag
bit (RABIF) in the INTCON register.
This interrupt can wake the device from the Sleep
mode, or any of the Idle modes. The user, in the
Interrupt Service Routine, can clear the interrupt in the
following manner:
a)
b)
A mismatch condition will continue to set the RABIF flag
bit. Reading or writing PORTB will end the mismatch
condition and allow the RABIF bit to be cleared. The latch
 2010 Microchip Technology Inc.
CLRF
CLRF
MOVLW
MOVWF
Any read or write of PORTB to clear the mis-
match condition (except when PORTB is the
source or destination of a MOVFF instruction).
Clear the flag bit, RABIF.
PORTB, TRISB and LATB
Registers
PORTB
LATB
0F0h
TRISB
; Initialize PORTB by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RB<7:4> as outputs
INITIALIZING PORTB
Preliminary
holding the last read value is not affected by a MCLR nor
Brown-out Reset. After either one of these Resets, the
RABIF flag will continue to be set if a mismatch is present.
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
All PORTB pins have individually controlled weak inter-
nal pull-up. When set, each bit of the WPUB register
enables the corresponding pin pull-up. When cleared,
the RABPU bit of the INTCON2 register enables pull-
ups on all pins which also have their corresponding
WPUB bit set. When set, the RABPU bit disables all
weak pull-ups. The weak pull-up is automatically turned
off when the port pin is configured as an output. The
pull-ups are disabled on a Power-on Reset.
Note:
Note:
PIC18F/LF1XK50
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RABIF
interrupt flag may not get set. Furthermore,
since a read or write on a port affects all
bits of that port, care must be taken when
using multiple pins in Interrupt-on-change
mode. Changes on one pin may not be
seen while servicing changes on another
pin.
On a Power-on Reset, RB<5:4> are
configured as analog inputs by default and
read as ‘0’.
DS41350E-page 89