PIC18F66J55-I/PT Microchip Technology, PIC18F66J55-I/PT Datasheet - Page 267

• Manufacturer Part Number: PIC18F66J55-I/PT
• Description: IC PIC MCU FLASH 48KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F66J55-I/PT

• Core Size: 8-Bit
• Program Memory Size: 96KB (48K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 49
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 49
• Ram Memory Size: 3904Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• Interface: I2C, SPI, USART
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: I2C, MSSP, SPI, EUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 49
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136, DM183022, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Operating Supply Voltage: 1.8|2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162087 - HEADER MPLAB ICD2 18F87J50 68/84MA180021 - MODULE PLUG-IN 18F87J50 FS USBAC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

19.4.8
To initiate a Start condition, the user sets the Start
Enable bit, SEN (SSPxCON2<0>). If the SDAx and
SCLx pins are sampled high, the Baud Rate Generator
is reloaded with the contents of SSPxADD<6:0> and
starts its count. If SCLx and SDAx are both sampled
high when the Baud Rate Generator times out (T
the SDAx pin is driven low. The action of the SDAx
being driven low while SCLx is high is the Start condi-
tion and causes the S bit (SSPxSTAT<3>) to be set.
Following this, the Baud Rate Generator is reloaded
with the contents of SSPxADD<6:0> and resumes its
count. When the Baud Rate Generator times out
(T
automatically cleared by hardware. The Baud Rate
Generator is suspended, leaving the SDAx line held low
and the Start condition is complete.
FIGURE 19-21:
© 2009 Microchip Technology Inc.
BRG
), the SEN bit (SSPxCON2<0>) will be
I
CONDITION TIMING
2
C MASTER MODE START
Write to SEN bit occurs here
FIRST START BIT TIMING
SDAx
SCLx
SDAx = 1,
SCLx = 1
T
BRG
BRG
),
Set S bit (SSPxSTAT<3>)
T
S
BRG
PIC18F87J50 FAMILY
At completion of Start bit,
hardware clears SEN bit
19.4.8.1
If the user writes the SSPxBUF when a Start sequence
is in progress, the WCOL bit is set and the contents of
the buffer are unchanged (the write doesn’t occur).
and sets SSPxIF bit
Note:
Note:
Write to SSPxBUF occurs here
T
BRG
1st bit
If, at the beginning of the Start condition,
the SDAx and SCLx pins are already sam-
pled low or if during the Start condition, the
SCLx line is sampled low before the SDAx
line is driven low, a bus collision occurs,
the Bus Collision Interrupt Flag, BCLxIF, is
set, the Start condition is aborted and the
I
Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPxCON2 is disabled until the Start
condition is complete.
2
C module is reset into its Idle state.
WCOL Status Flag
T
BRG
2nd bit
DS39775C-page 267