DSPIC33FJ16MC304-I/ML Microchip Technology, DSPIC33FJ16MC304-I/ML Datasheet - Page 215

• Manufacturer Part Number: DSPIC33FJ16MC304-I/ML
• Description: IC DSPIC MCU/DSP 16K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ16MC304-I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 9x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: I2C, SPI, UART
• No. Of I/o's: 35
• Flash Memory Size: 16KB
• Supply Voltage Range: 3V To 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164335 - MODULE SKT FOR 10X10 PM3 44TQFPDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

21.2
The
dsPIC33FJ16MC304 devices power their core digital
logic at a nominal 2.5V. This can create a conflict for
designs that are required to operate at a higher typical
voltage, such as 3.3V. To simplify system design, all
devices
dsPIC33FJ16MC304 family incorporate an on-chip
regulator that allows the device to run its core logic from
V
The regulator provides power to the core from the other
V
(less than 5 ohms) capacitor (such as tantalum or
ceramic) must be connected to the V
(Figure
regulator. The recommended value for the filter capac-
itor is provided in
“DC
On a POR
voltage regulator to generate an output voltage. During
this time, designated as T
disabled. T
resumes operation after any power-down.
FIGURE 21-1:
© 2011 Microchip Technology Inc.
DD
DD
Note:
Note 1:
.
pins. When the regulator is enabled, a low-ESR
Characteristics”.
21-1). This helps to maintain the stability of the
2:
On-Chip Voltage Regulator
C
10
,
EFC
in
STARTUP
it takes approximately 20 μs for the on-chip
It is important for low-ESR capacitors to
be placed as close as possible to the V
pin.
μ
dsPIC33FJ32MC202/204 and dsPIC33FJ16MC304
F
These are typical operating voltages. Refer
to
Characteristics”
ranges of V
It is important for low-ESR capacitors to be
placed as close as possible to the V
pin.
dsPIC33FJ32MC202/204
3.3V
Table 24-13
the
Table 24-13
is applied every time the device
dsPIC33FJ32MC202/204
CONNECTIONS FOR THE
ON-CHIP VOLTAGE
REGULATOR
V
V
V
DD
DD
CAP
SS
dsPIC33F
located in
and V
STARTUP
for the full operating
located in
CAP
, code execution is
.
Section 24.1 “DC
(1)
Section 24.1
CAP
CAP
CAP
and
and
pin
21.3
The Brown-out Reset (BOR) module is based on an
internal voltage reference circuit that monitors the reg-
ulated supply voltage V
BOR module is to generate a device Reset when a
brown-out condition occurs. Brown-out conditions are
generally caused by glitches on the AC mains (for
example, missing portions of the AC cycle waveform
due to bad power transmission lines, or voltage sags
due to excessive current draw when a large inductive
load is turned on).
A BOR generates a Reset pulse, which resets the
device. The BOR selects the clock source, based on
the device Configuration bit values (FNOSC<2:0> and
POSCMD<1:0>).
If an oscillator mode is selected, the BOR activates the
Oscillator Start-up Timer (OST). The system clock is
held until OST expires. If the PLL is used, the clock is
held until the LOCK bit (OSCCON<5>) is ‘1’.
Concurrently, the PWRT time-out (TPWRT) is applied
before the internal Reset is released. If TPWRT = 0 and
a crystal oscillator is being used, then a nominal delay
of TFSCM = 100 is applied. The total delay in this case
is TFSCM.
The BOR Status bit (RCON<1>) is set to indicate that a
BOR has occurred. The BOR circuit continues to oper-
ate while in Sleep or Idle modes and resets the device
should VDD fall below the BOR threshold voltage.
BOR: Brown-Out Reset
CAP
. The main purpose of the
DS70283H-page 215