PIC16F737-I/SP Microchip Technology, PIC16F737-I/SP Datasheet - Page 236

• Manufacturer Part Number: PIC16F737-I/SP
• Description: IC PIC MCU FLASH 4KX14 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F737-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: AUSART/CCP/I2C/MSSP/SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 3
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3DBF777 - BOARD DAUGHTER ICEPIC3
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F7X7
FIGURE 18-18:
TABLE 18-13: AUSART SYNCHRONOUS TRANSMISSION REQUIREMENTS
FIGURE 18-19:
TABLE 18-14: AUSART SYNCHRONOUS RECEIVE REQUIREMENTS
DS30498C-page 234
120
121
122
125
126
Param
Param
Note: Refer to Figure 18-4 for load conditions.
No.
No.
RC7/RX/DT
RC6/TX/CK
† Data in “Typ” column is at 5V, 25 C unless otherwise stated. These parameters are for design guidance
† Data in “Typ” column is at 5V, 25 C unless otherwise stated. These parameters are for design guidance
Note: Refer to Figure 18-4 for load conditions.
T
T
T
T
T
RC7/RX/DT
RC6/TX/CK
CK
Symbol
CK
CKRF
DT
DTRF
Symbol
pin
pin
only and are not tested.
only and are not tested.
L2
H2
V2
DTL
CK
DT
pin
pin
L
V SYNC XMIT (MASTER & SLAVE)
Clock High to Data Out Valid
Clock Out Rise Time and Fall Time
(Master mode)
Data Out Rise Time and Fall Time
SYNC RCV (MASTER & SLAVE)
Data Setup before CK
Data Hold after CK
AUSART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
AUSART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
121
120
Characteristic
Characteristic
(DT hold time)
125
(DT setup time)
121
PIC16F7X7
PIC16LF7X7
PIC16F7X7
PIC16LF7X7
PIC16F7X7
PIC16LF7X7
126
Min
15
15
Typ†
—
—
Min
—
—
—
—
—
—
122
Typ† Max Units Conditions
Max
—
—
—
—
—
—
—
—
 2004 Microchip Technology Inc.
100
80
45
50
45
50
Units
ns
ns
ns
ns
ns
ns
ns
ns
Conditions