PIC24FJ64GA008-I/PT Microchip Technology, PIC24FJ64GA008-I/PT Datasheet - Page 48
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC24FJ64GA008-I/PT
Manufacturer Part Number
PIC24FJ64GA008-I/PT
Description
IC PIC MCU FLASH 32KX16 80TQFP
Manufacturer
Microchip Technology
Series
PIC® 24Fr
Datasheets
1.PIC24FJ16GA002-ISS.pdf
(52 pages)
2.PIC24FJ64GA006-IPT.pdf
(240 pages)
3.PIC24FJ64GA006-IPT.pdf
(22 pages)
Specifications of PIC24FJ64GA008-I/PT
Core Size
16-Bit
Program Memory Size
64KB (22K x 24)
Core Processor
PIC
Speed
16MHz
Connectivity
I²C, PMP, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
69
Program Memory Type
FLASH
Ram Size
8K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
80-TFQFP
Controller Family/series
PIC24
No. Of I/o's
69
Ram Memory Size
8192Byte
Cpu Speed
32MHz
No. Of Timers
5
Interface
I2C, SPI, USART
Embedded Interface Type
I2C, SPI, USART
Rohs Compliant
Yes
Processor Series
PIC24FJ
Core
PIC
Data Bus Width
16 bit
Data Ram Size
8 KB
Interface Type
I2C, SPI, UART
Maximum Clock Frequency
32 MHz
Number Of Programmable I/os
69
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52713-733, 52714-737, 53276-922, EWDSPIC
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM240011, DV164033, MA240011, AC164127, DM240001
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 16 Channel
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
876-1004 - PIC24 BREAKOUT BOARDDM240011 - KIT STARTER MPLAB FOR PIC24F MCUDV164033 - KIT START EXPLORER 16 MPLAB ICD2MA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164328 - MODULE SKT FOR 80TQFP
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC24FJ64GA008-I/PT
Manufacturer:
TI
Quantity:
15 000
Company:
Part Number:
PIC24FJ64GA008-I/PT
Manufacturer:
MICROCHIP
Quantity:
220
Company:
Part Number:
PIC24FJ64GA008-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
PIC24FJ128GA010 FAMILY
4.2
The PIC24F Flash program memory array is organized
into rows of 64 instructions or 192 bytes. RTSP allows
the user to erase blocks of eight rows (512 instructions)
at a time and to program one row at a time. It is also
possible to program single words.
The 8-row erase blocks and single row write blocks are
edge-aligned, from the beginning of program memory,
on boundaries of 1536 bytes and 192 bytes,
respectively.
When data is written to program memory using TBLWT
instructions, the data is not written directly to memory.
Instead, data written using table writes is stored in
holding latches until the programming sequence is
executed.
Any number of TBLWT instructions can be executed
and a write will be successfully performed. However, 64
TBLWT instructions are required to write the full row of
memory.
To ensure that no data is corrupted during a write, any
unused addresses should be programmed with
FFFFFFh. This is because the holding latches reset to
an unknown state, so if the addresses are left in the
Reset state, they may overwrite the locations on rows
which were not rewritten.
The basic sequence for RTSP programming is to set up
a Table Pointer, then do a series of TBLWT instructions
to load the buffers. Programming is performed by
setting the control bits in the NVMCON register.
Data can be loaded in any order and the holding regis-
ters can be written to multiple times before performing
a write operation. Subsequent writes, however, will
wipe out any previous writes.
All of the table write operations are single-word writes
(2 instruction cycles), because only the buffers are
written.
programming each row
4.3
The PIC24F family supports JTAG programming and
boundary scan. Boundary scan can improve the manu-
facturing process by verifying pin to PCB connectivity.
Programming can be performed with industry standard
JTAG programmers supporting Serial Vector Format
(SVF).
DS39747E-page 48
Note:
RTSP Operation
JTAG Operation
A
Writing to a location multiple times without
erasing is not recommended.
programming
cycle
is
required
for
4.4
Enhanced In-Circuit Serial Programming uses an on-
board bootloader, known as the program executive, to
manage the programming process. Using an SPI data
frame format, the program executive can erase,
program and verify program memory. See the device
programming specification for more information on
Enhanced ICSP
4.5
There are two SFRs used to read and write the
program Flash memory: NVMCON and NVMKEY.
The NVMCON register (Register 4-1) controls which
blocks are to be erased, which memory type is to be
programmed and the start of the programming cycle.
NVMKEY is a write-only register that is used for write
protection. To start a programming or erase sequence,
the user must consecutively write 55h and AAh to the
NVMKEY register. Refer to Section 4.6 “Programming
Operations” for further details.
4.6
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode. During a programming or an erase operation,
the processor stalls (waits) until the operation is
finished. Setting the WR bit (NVMCON<15>) starts the
operation, and the WR bit is automatically cleared
when the operation is finished.
Configuration Word values are stored in the last two
locations of program memory. Performing a page erase
operation on the last page of program memory clears
these values and enables code protection. As a result,
avoid performing page erase operations on the last
page of program memory.
Enhanced In-Circuit Serial
Programming
Control Registers
Programming Operations
© 2009 Microchip Technology Inc.