PIC16C71-04I/P Microchip Technology, PIC16C71-04I/P Datasheet - Page 141

• Manufacturer Part Number: PIC16C71-04I/P
• Description: IC MCU OTP 1KX14 A/D 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C71-04I/P

• Program Memory Type: OTP
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 13
• Ram Size: 36 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 6 V
• Data Converters: A/D 4x8b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 36 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 1
• Operating Supply Voltage: 2.5 V to 6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 8-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1059 - ADAPTER 18 ZIF BD W/18SO PLUGSDVA16XP180 - ADAPTER DEVICE FOR MPLAB-ICEAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

15.5
FIGURE 15-2: EXTERNAL CLOCK TIMING
TABLE 15-2:
Note 1: Instruction cycle period (T
Parameter
1997 Microchip Technology Inc.
CLKOUT
OSC1
No.
†
1
2
3
4
Timing Diagrams and Specifications
Data in "Typ" column is at 5V, 25˚C unless otherwise stated. These parameters are for design guidance only and are not
tested.
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin.
When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. OSC2 is disconnected
(has no loading) for the PIC16C71.
TosR,
TosL,
TosH
Sym
Fosc
TosF
Tosc
T
CY
EXTERNAL CLOCK TIMING REQUIREMENTS
Characteristic
External CLKIN Frequency
(Note 1)
Oscillator Frequency
(Note 1)
External CLKIN Period
(Note 1)
Oscillator Period
(Note 1)
Instruction Cycle Time (Note 1)
External Clock in (OSC1) High or
Low Time
External Clock in (OSC1) Rise or
Fall Time
Q4
CY
) equals four times the input oscillator time-base period. All specified values are based on
Q1
1
Q2
Min
250
250
250
250
250
DC
DC
DC
DC
DC
0.1
1.0
2.5
50
50
50
10
25
50
15
1
1
5
5
2
Typ†
T
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
3
CY
Q3
Applicable Devices
10,000
1,000
1,000
3
Max
200
DC
20
20
—
—
—
—
—
—
—
—
—
—
—
—
4
4
4
4
4
4
Units Conditions
MHz
MHz
MHz
MHz
MHz
MHz
MHz
kHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Q4
s
s
s
s
PIC16C71X
XT osc mode
HS osc mode (-04)
HS osc mode
LP osc mode
RC osc mode
LP osc mode
T
XT oscillator
LP oscillator
HS oscillator
XT oscillator
LP oscillator
HS oscillator
HS osc mode (-20)
LP osc mode
RC osc mode
XT osc mode
HS osc mode
XT osc mode
HS osc mode (-04)
HS osc mode (-20)
XT osc mode
HS osc mode (-04)
HS osc mode (-20)
CY
= 4/Fosc
4
710 71 711 715
DS30272A-page 141
Q1