PIC24FJ192GA106-I/PT Microchip Technology, PIC24FJ192GA106-I/PT Datasheet - Page 165

• Manufacturer Part Number: PIC24FJ192GA106-I/PT
• Description: IC PIC MCU FLASH 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ192GA106-I/PT

• Core Size: 16-Bit
• Program Memory Size: 192KB (65.5K x 24)
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Number Of I /o: 53
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 53
• Ram Memory Size: 16KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 16 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 53
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240011, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC24
• Maximum Speed: 32 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCU
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

To set up the SPI module for the Enhanced Buffer
Master mode of operation:
1.
2.
3.
4.
5.
6.
FIGURE 14-2:
© 2008 Microchip Technology Inc.
SSx/FSYNCx
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1 and
SPIxCON2 registers with the MSTEN bit
(SPIxCON1<5>) = 1.
Clear the SPIROV bit (SPIxSTAT<6>).
Select Enhanced Buffer mode by setting the
SPIBEN bit (SPIxCON2<0>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Write the data to be transmitted to the SPIxBUF
register. Transmission (and reception) will start
as soon as data is written to the SPIxBUF
register.
SDOx
SCKx
SDIx
Clear the SPIxIF bit in the respective IFS
register.
Set the SPIxIE bit in the respective IEC
register.
Write the SPIxIP bits in the respective IPC
register.
Read SPIxBUF
Control
Transfer
Sync
SPIx MODULE BLOCK DIAGRAM (ENHANCED MODE)
Receive Buffer
8-Level FIFO
bit0
SPIxSR
Control
SPIxBUF
Clock
Shift Control
Transmit Buffer
8-Level FIFO
PIC24FJ256GA110 FAMILY
Preliminary
Transfer
Write SPIxBUF
Select
Edge
To set up the SPI module for the Enhanced Buffer
Slave mode of operation:
1.
2.
3.
4.
5.
6.
7.
8.
16
Clear the SPIxBUF register.
If using interrupts:
a)
b)
c)
Write the desired settings to the SPIxCON1 and
SPIxCON2 registers with the MSTEN bit
(SPIxCON1<5>) = 0.
Clear the SMP bit.
If the CKE bit is set, then the SSEN bit must be
set, thus enabling the SSx pin.
Clear the SPIROV bit (SPIxSTAT<6>).
Select Enhanced Buffer mode by setting the
SPIBEN bit (SPIxCON2<0>).
Enable SPI operation by setting the SPIEN bit
(SPIxSTAT<15>).
Secondary
Clear the SPIxIF bit in the respective IFS
register.
Set the SPIxIE bit in the respective IEC
register.
Write the SPIxIP bits in the respective IPC
register to set the interrupt priority.
Prescaler
1:1 to 1:8
Internal Data Bus
1:1/4/16/64
Prescaler
Primary
DS39905B-page 163
SPIxCON1<1:0>
SPIxCON1<4:2>
Enable
Master Clock
F
CY