PIC24FJ128GA110-I/PT Microchip Technology, PIC24FJ128GA110-I/PT Datasheet - Page 110

• Manufacturer Part Number: PIC24FJ128GA110-I/PT
• Description: IC PIC MCU FLASH 100TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ128GA110-I/PT

• Core Size: 16-Bit
• Program Memory Size: 128KB (43K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Controller Family/series: PIC24
• No. Of I/o's: 85
• Ram Memory Size: 16KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDMA240015 - BOARD MCV PIM FOR 24F256GADM240011 - KIT STARTER MPLAB FOR PIC24F MCU
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC24FJ256GA110 FAMILY
REGISTER 7-3:
7.4
With few limitations, applications are free to switch
between any of the four clock sources (POSC, SOSC,
FRC and LPRC) under software control and at any
time. To limit the possible side effects that could result
from this flexibility, PIC24F devices have a safeguard
lock built into the switching process.
DS39905B-page 108
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15-6
bit 5-0
Note 1:
Note:
U-0
U-0
—
—
Clock Switching Operation
Increments or decrements of TUN5:TUN0 may not change the FRC frequency in equal steps over the
FRC tuning range, and may not be monotonic.
The primary oscillator mode has three
different submodes (XT, HS and EC)
which are determined by the POSCMDx
Configuration bits. While an application
can switch to and from primary oscillator
mode in software, it cannot switch
between the different primary submodes
without reprogramming the device.
Unimplemented: Read as ‘0’
TUN5:TUN0: FRC Oscillator Tuning bits
011111 = Maximum frequency deviation
011110 =
•
•
•
000001 =
000000 = Center frequency, oscillator is running at factory calibrated frequency
111111 =
•
•
•
100001 =
100000 = Minimum frequency deviation
U-0
U-0
—
—
OSCTUN: FRC OSCILLATOR TUNE REGISTER
W = Writable bit
‘1’ = Bit is set
TUN5
R/W-0
U-0
—
(1)
TUN4
R/W-0
U-0
—
Preliminary
(1)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
TUN3
R/W-0
7.4.1
To enable clock switching, the FCKSM1 Configuration
bit in CW 2 must be programmed to ‘0’. (Refer to
Section 24.1 “Configuration Bits” for further details.)
If the FCKSM1 Configuration bit is unprogrammed (‘1’),
the clock switching function and Fail-Safe Clock Monitor
function are disabled. This is the default setting.
The NOSCx control bits (OSCCON<10:8>) do not
control the clock selection when clock switching is dis-
abled. However, the COSCx bits (OSCCON<14:12>)
will reflect the clock source selected by the FNOSCx
Configuration bits.
The OSWEN control bit (OSCCON<0>) has no effect
when clock switching is disabled. It is held at ‘0’ at all
times.
U-0
—
(1)
ENABLING CLOCK SWITCHING
TUN2
R/W-0
U-0
—
(1)
© 2008 Microchip Technology Inc.
x = Bit is unknown
TUN1
R/W-0
U-0
—
(1)
TUN0
R/W-0
U-0
—
(1)
bit 8
bit 0