PIC16C74B-04I/P Microchip Technology, PIC16C74B-04I/P Datasheet - Page 55
![IC MCU OTP 4KX14 A/D PWM 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
PIC16C74B-04I/P
Manufacturer Part Number
PIC16C74B-04I/P
Description
IC MCU OTP 4KX14 A/D PWM 40DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C63A-04SP.pdf
(184 pages)
4.PIC16C63A-04SP.pdf
(10 pages)
5.PIC16C63A-04SP.pdf
(10 pages)
Specifications of PIC16C74B-04I/P
Core Size
8-Bit
Program Memory Size
7KB (4K x 14)
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Core Processor
PIC
Speed
4MHz
Connectivity
I²C, SPI, UART/USART
Number Of I /o
33
Program Memory Type
OTP
Ram Size
192 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 5.5 V
Data Converters
A/D 8x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
40-DIP (0.600", 15.24mm)
Controller Family/series
PIC16C
No. Of I/o's
33
Ram Memory Size
192Byte
Cpu Speed
4MHz
No. Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
444-1001 - DEMO BOARD FOR PICMICRO MCU
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PIC16C74B-04I/PQ
Manufacturer:
Microchip Technology
Quantity:
10 000
Company:
Part Number:
PIC16C74B-04I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
10.0
10.1
The Synchronous Serial Port (SSP) module is a serial
interface useful for communicating with other periph-
eral or microcontroller devices. These peripheral
devices may be Serial EEPROMs, shift registers, dis-
play drivers, A/D converters, etc. The SSP module can
operate in one of two modes:
• Serial Peripheral Interface (SPI)
• Inter-Integrated Circuit (I
An overview of I
tion on the SSP module can be found in the PICmicro™
Mid-Range
(DS33023).
Refer to Application Note AN578, “Use of the SSP
Module in the I
10.2
This section contains register definitions and opera-
tional characteristics of the SPI module.
SPI mode allows 8 bits of data to be synchronously
transmitted and received simultaneously. To accom-
plish communication, typically three pins are used:
• Serial Data Out (SDO) RC5/SDO
• Serial Data In (SDI) RC4/SDI/SDA
• Serial Clock (SCK) RC3/SCK/SCL
Additionally, a fourth pin may be used when in a Slave
mode of operation:
• Slave Select (SS) RA5/SS/AN4
When initializing the SPI, several options need to be
specified. This is done by programming the appropriate
control bits in the SSPCON register (SSPCON<5:0>)
and SSPSTAT<7:6>. These control bits allow the fol-
lowing to be specified:
• Master mode (SCK is the clock output)
• Slave mode (SCK is the clock input)
• Clock Polarity (Idle state of SCK)
• Clock edge (output data on rising/falling edge of
• Clock Rate (Master mode only)
• Slave Select mode (Slave mode only)
SCK)
2000 Microchip Technology Inc.
SYNCHRONOUS SERIAL PORT
(SSP) MODULE
SSP Module Overview
SPI Mode
MCU
2
C Multi-Master Environment.”
2
C operations and additional informa-
Family
2
C)
Reference
Manual
PIC16C63A/65B/73B/74B
FIGURE 10-1:
To enable the serial port, SSP enable bit, SSPEN
(SSPCON<5>) must be set. To reset or reconfigure SPI
mode, clear bit SSPEN, re-initialize the SSPCON reg-
ister, and then set bit SSPEN. This configures the SDI,
SDO, SCK, and SS pins as serial port pins. For the pins
to behave as the serial port function, they must have
their data direction bits (in the TRISC register) appro-
priately programmed. That is:
• SDI must have TRISC<4> set
• SDO must have TRISC<5> cleared
• SCK (Master mode) must have TRISC<3> cleared
• SCK (Slave mode) must have TRISC<3> set
• SS must have TRISA<5> set
• ADCON1 must configure RA5 as a digital I/O pin.
.
RC4/SDI/SDA
RA5/SS/AN4
Note 1: When the SPI is in Slave mode with SS
RC3/SCK/
RC5/SDO
SCL
2: If the SPI is used in Slave mode with
pin control enabled (SSPCON<3:0> =
0100), the SPI module will reset if the SS
pin is set to V
CKE = '1', then the SS pin control must be
enabled.
Read
SS Control
Select
TRISC<3>
Edge
SSP BLOCK DIAGRAM
(SPI MODE)
Enable
SSPM3:SSPM0
bit0
Select
Edge
SSPBUF reg
DD
SSPSR reg
.
Clock Select
4
2
DS30605C-page 55
Prescaler
TMR2 Output
4, 16, 64
Write
Clock
Shift
Data Bus
Internal
2
T
CY