DSPIC33FJ256MC510-I/PT Microchip Technology, DSPIC33FJ256MC510-I/PT Datasheet - Page 40

• Manufacturer Part Number: DSPIC33FJ256MC510-I/PT
• Description: IC DSPIC MCU/DSP 256K 100TQFP
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ256MC510-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 24x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TFQFP
• Core Frequency: 40MHz
• Core Supply Voltage: 2.75V
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of I/o's: 85
• Flash Memory Size: 256KB
• Supply Voltage Range: 3V To 3.6V
• Package: 100TQFP
• Device Core: dsPIC
• Family Name: dSPIC33
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 85
• Interface Type: CAN/I2C/SPI/UART
• On-chip Adc: 24-chx12-bit
• Number Of Timers: 9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1001 - DSPIC33 BREAKOUT BOARDMA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TABLE 5-5:
FIGURE 5-8:
DS70152H-page 40
Step 8: Wait for Row Program operation to complete and make sure WR bit is clear.
Step 9: Repeat steps 3-8 until all code memory is programmed.
Command
(Binary)
0000
0000
0000
0001
0000
0000
—
—
SERIAL INSTRUCTION EXECUTION FOR WRITING CODE MEMORY (CONTINUED)
803B00
883C20
000000
<VISI>
040200
000000
(Hex)
PROGRAM CODE MEMORY FLOW
Data
—
—
LoopCount + 1
LoopCount =
N = 1
Externally time ‘P13’ msec (see
Timing
complete.
MOV
MOV
NOP
Clock out contents of VISI register.
GOTO
NOP
Repeat until the WR bit is clear.
Requirements”) to allow sufficient time for the Row Program operation to
NVMCON, W0
W0, VISI
0x200
N = N + 1
No
No
Start Write Sequence
and Poll for WR bit
Buffer at <Addr>
Load 2 Bytes
to be cleared
Section 8.0 “AC/DC Characteristics and
Device for
Configure
locations
to Write
written?
Description
Writes
done?
bytes
Start
End
All
All
Yes
Yes
N = 1
LoopCount = 0
© 2010 Microchip Technology Inc.