STM32F101R8T6 STMicroelectronics, STM32F101R8T6 Datasheet - Page 49

• Manufacturer Part Number: STM32F101R8T6
• Description: MCU ARM 64KB FLASH/TIMER 64-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101R8T6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 10 KB
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 12-bit
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6058

STM32F101x8, STM32F101xB
5.3.8
5.3.9
All timings are derived from tests performed under the ambient temperature and V
voltage conditions summarized in
Table 25.
1. The wakeup times are measured from the wakeup event to the point at which the user application code
PLL characteristics
The parameters given in
temperature and V
Table 26.
1. Based on device characterization, not tested in production.
2. Take care of using the appropriate multiplier factors so as to have PLL input clock values compatible with
Memory characteristics
Flash memory
The characteristics are given at T
Table 27.
f
f
t
Jitter
PLL_IN
PLL_OUT
LOCK
Symbol
t
ERASE
reads the first instruction.
the range defined by f
t
t
t
t
Symbol
prog
t
WUSLEEP
WUSTDBY
ME
WUSTOP
Symbol
16-bit programming time
Page (1 KB) erase time
Mass erase time
(1)
(1)
(1)
Low-power mode wakeup timings
PLL characteristics
Flash memory characteristics
PLL input clock
PLL input clock duty cycle
PLL multiplier output clock
PLL lock time
Cycle-to-cycle jitter
Parameter
DD
Wakeup from Sleep mode
Wakeup from Stop mode (regulator in run mode)
Wakeup from Stop mode (regulator in low-power mode)
Wakeup from Standby mode
PLL_OUT
supply voltage conditions summarized in
Table 26
.
Parameter
Doc ID 13586 Rev 13
(2)
A
Table
are derived from tests performed under the ambient
= –40 to 85 °C unless otherwise specified.
Parameter
T
T
T
8.
A
A
A
–40 to +85 °C
–40 to +85 °C
–40 to +85 °C
Conditions
Min
40
16
1
(1)
Min
Table
20
20
40
Electrical characteristics
Value
Typ
8.0
(1)
8.
52.5
Typ
Typ
1.8
3.6
5.4
Max
50
300
200
25
60
36
Max
(1)
70
40
40
DD
(1)
supply
Unit
MHz
MHz
Unit
µs
µs
µs
µs
ps
Unit
%
ms
ms
49/85
µs