STM32F102C8T6 STMicroelectronics, STM32F102C8T6 Datasheet - Page 25
![MCU ARM 32BIT 64KB FLASH 48-LQFP](/photos/12/15/121518/stmicroelectronics-48-lqfp_sml.jpg)
STM32F102C8T6
Manufacturer Part Number
STM32F102C8T6
Description
MCU ARM 32BIT 64KB FLASH 48-LQFP
Manufacturer
STMicroelectronics
Series
STM32r
Datasheet
1.STEVAL-MKI109V1.pdf
(69 pages)
Specifications of STM32F102C8T6
Core Processor
ARM® Cortex-M3™
Core Size
32-Bit
Speed
48MHz
Connectivity
I²C, IrDA, LIN, SPI, UART/USART, USB
Peripherals
DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
Number Of I /o
37
Program Memory Size
64KB (64K x 8)
Program Memory Type
FLASH
Ram Size
10K x 8
Voltage - Supply (vcc/vdd)
2 V ~ 3.6 V
Data Converters
A/D 10x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
48-LQFP
For Use With
497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / Rohs Status
Details
Other names
497-8307
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STM32F102C8T6
Manufacturer:
ST
Quantity:
177
Company:
Part Number:
STM32F102C8T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STM32F102C8T6TR
Manufacturer:
STMicroelectronics
Quantity:
10 000
STM32F102x8, STM32F102xB
5.1.7
5.2
Current consumption measurement
Figure 9.
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 6: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 5.
1. All main power (V
2. I
|V
V
V
Symbol
SSX
DD
|V
ESD(HBM)
supply, in the permitted range.
maximum is respected. If V
externally to the I
induced by V
INJ(PIN)
V
V
DDx
IN
V
SS
|
SS
must never be exceeded (see
|
Current consumption measurement scheme
Voltage characteristics
IN
External main supply voltage (including
V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all the different ground
pins
Electrostatic discharge voltage (human body
model)
DDA
<V
characteristics, and
INJ(PIN)
DD
SS
and V
.
, V
DDA
value. A positive injection is induced by V
DD
) and ground (V
IN
)
maximum cannot be respected, the injection current must be limited
(1)
Ratings
Doc ID 15056 Rev 3
Table 6: Current
Table 7: Thermal characteristics
I DD _V BAT
SS
, V
I DD
(2)
DD
SSA
power pins
) pins must always be connected to the external power
V DD
V DDA
V BAT
(2)
characteristics). This is implicitly insured if V
Table 5: Voltage
see
maximum ratings (electrical
IN
ai14126
V
V
> V
SS
SS
Section 5.3.11: Absolute
–0.3
Min
IN
0.3
0.3
max while a negative injection is
sensitivity)
Electrical characteristics
may cause permanent
V
characteristics,
DD
Max
+5.5
4.0
50
50
+0.3
IN
Unit
mV
V
25/69