STM32F101CBT6 STMicroelectronics, STM32F101CBT6 Datasheet - Page 31

• Manufacturer Part Number: STM32F101CBT6
• Description: MCU ARM 32KB FLASH/TIMER 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101CBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 12-bit
• Controller Family/series: (ARM Cortex) STM32
• No. Of I/o's: 37
• Ram Memory Size: 16KB
• Cpu Speed: 36MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6287

STM32F101x8, STM32F101xB
5.1.7
5.2
Current consumption measurement
Figure 12. Current consumption measurement scheme
Absolute maximum ratings
Stresses above the absolute maximum ratings listed in
Table 6: Current
damage to the device. These are stress ratings only and functional operation of the device
at these conditions is not implied. Exposure to maximum rating conditions for extended
periods may affect device reliability.
Table 5.
1. All main power (V
2. I
|V
V
V
Symbol
SSX
DD
|V
ESD(HBM)
supply, in the permitted range.
maximum is respected. If V
externally to the I
induced by V
INJ(PIN)
V
 V
DDx
IN
V
SS
|
SS
must never be exceeded (see
|
Voltage characteristics
External main supply voltage (including
V
Input voltage on five volt tolerant pin
Input voltage on any other pin
Variations between different V
Variations between all the different ground
pins
Electrostatic discharge voltage (human body
model)
IN
DDA
<V
characteristics, and
INJ(PIN)
DD
SS
and V
.
, V
DDA
value. A positive injection is induced by V
DD
) and ground (V
IN
)
maximum cannot be respected, the injection current must be limited
(1)
Doc ID 13586 Rev 13
Ratings
Table 6: Current
Table 7: Thermal characteristics
I DD _V BAT
SS
, V
I DD
(2)
DD
SSA
power pins
) pins must always be connected to the external power
V DD
V DDA
V BAT
(2)
characteristics). This is implicitly insured if V
Table 5: Voltage
see
maximum ratings (electrical
IN
ai14126
V
V
> V
SS
SS
Section 5.3.11: Absolute
–0.3
Min
IN
 0.3
0.3
max while a negative injection is
sensitivity)
Electrical characteristics
may cause permanent
V
characteristics,
DD
Max
+5.5
4.0
50
50
+0.3
IN
Unit
mV
V
31/85