C8051F562-IQ Silicon Laboratories Inc, C8051F562-IQ Datasheet - Page 238

• Manufacturer Part Number: C8051F562-IQ
• Description: IC 8051 MCU 32K FLASH 32-QFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F56xr

Specifications of C8051F562-IQ

• Program Memory Type: FLASH
• Program Memory Size: 32KB (32K x 8)
• Package / Case: 32-QFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 50MHz
• Connectivity: SMBus (2-Wire/I²C), LIN, SPI, UART/USART
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 25
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.25 V
• Data Converters: A/D 25x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: C8051F5x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 2304 B
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 25
• Operating Supply Voltage: 1.8 V to 5.25 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F560DK
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1691 - KIT DEVELOPMENT FOR C8051F560
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1698

C8051F55x/56x/57x
SFR Definition 23.1. SCON0: Serial Port 0 Control
SFR Address = 0x98; Bit-Addressable; SFR Page = 0x00
238
Name
Reset
Bit
Type
7
6
5
4
3
2
1
0
Bit
PERR0
THRE0
Name
OVR0
REN0
RBX0
TBX0
RI0
TI0
OVR0
R/W
7
0
Receive FIFO Overrun Flag.
0: Receive FIFO Overrun has not occurred
1: Receive FIFO Overrun has occurred; A received character has been discarded due
to a full FIFO.
Parity Error Flag.
When parity is enabled, this bit indicates that a parity error has occurred. It is set to 1
when the parity of the oldest byte in the FIFO does not match the selected Parity Type.
0: Parity error has not occurred
1: Parity error has occurred.
This bit must be cleared by software.
Transmit Holding Register Empty Flag.
0: Transmit Holding Register not Empty—do not write to SBUF0.
1: Transmit Holding Register Empty—it is safe to write to SBUF0.
Receive Enable.
This bit enables/disables the UART receiver. When disabled, bytes can still be read
from the receive FIFO.
0: UART1 reception disabled.
1: UART1 reception enabled.
Extra Transmission Bit.
The logic level of this bit will be assigned to the extra transmission bit when XBE0 is set
to 1. This bit is not used when Parity is enabled.
Extra Receive Bit.
RBX0 is assigned the value of the extra bit when XBE1 is set to 1. If XBE1 is cleared to
0, RBX1 will be assigned the logic level of the first stop bit. This bit is not valid when
Parity is enabled.
Transmit Interrupt Flag.
Set to a 1 by hardware after data has been transmitted, at the beginning of the STOP
bit. When the UART0 interrupt is enabled, setting this bit causes the CPU to vector to
the UART0 interrupt service routine. This bit must be cleared manually by software.
Receive Interrupt Flag.
Set to 1 by hardware when a byte of data has been received by UART0 (set at the
STOP bit sampling time). When the UART0 interrupt is enabled, setting this bit to 1
causes the CPU to vector to the UART0 interrupt service routine. This bit must be
cleared manually by software. Note that RI0 will remain set to ‘1’ as long as there is
data still in the UART FIFO. After the last byte has been shifted from the FIFO to
SBUF0, RI0 can be cleared.
PERR0
R/W
6
0
THRE0
R
5
1
REN0
R/W
Rev. 1.1
4
0
Function
TBX0
R/W
3
0
RBX0
R/W
2
0
R/W
TI0
1
0
R/W
RI0
0
0