PIC16F726-I/SO Microchip Technology, PIC16F726-I/SO Datasheet - Page 23

• Manufacturer Part Number: PIC16F726-I/SO
• Description: IC PIC MCU FLASH 8KX14 28-SOIC
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16F726-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 14KB (8K x 14)
• Package / Case: 28-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 368 B
• Interface Type: I2C/SCI/SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 25
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 11-ch x 8-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPICE2000 - EMULATOR MPLAB-ICE 2000 POD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7.0
In the hex file there are two bytes per program word
stored in the Intel
LSB first, MSB second. Because there are two bytes
per word, the addresses in the hex file are 2x the
address
Configuration Word 1 is stored at 2007h on the
PIC16F72X/PIC16LF72X. In the hex file this will be at
location 400Eh-400Fh).
7.1
To allow portability of code, it is strongly recommended
that the programmer is able to read the Configuration
Words and user ID locations from the hex file. If the
Configuration Words information was not present in the
hex file, a simple warning message may be issued.
Similarly, while saving a hex file, Configuration Words
and user ID information should be included.
EXAMPLE 7-1:
 2010 Microchip Technology Inc.
PIC16F726
HEX FILE USAGE
Configuration Word
in
program
®
Sum of Memory addresses 0000h-1FFFh
Configuration Word 1
Configuration Word 1 mask
Configuration Word 2
Configuration Word 2 mask
Checksum
INH8M hex format. Data is stored
CHECKSUM COMPUTED WITH CODE PROTECTION DISABLED
memory.
(Example:
= 2534h + (2AC3h and 3F7Fh) + (3FEFh and 0030h)
= 2534h + 2A43h + 0020h
= 4F97h
Advance Information
The
PIC16F72X/PIC16LF72X
7.2
If a device ID is present in the hex file at 400Ch-400Dh
(2006h on the part), the programmer should verify the
device ID/revision against the value read from the part.
On a mismatch condition, the programmer should
generate a warning message.
7.3
The checksum is calculated by two different methods,
dependent on the setting of the CP Configuration bit.
7.3.1
With the code protection disabled, the checksum is
computed by reading the contents of the PIC16F72X/
PIC16LF72X program memory locations and adding
up the program memory data, starting at address
0000h, up to the maximum user addressable location
(e.g., 1FFFH for the PIC16F726). Any Carry bit
exceeding 16 bits are neglected. Additionally, the rele-
vant bits of the Configuration Words are added to the
checksum. All unused Configuration bits are masked to
‘0’.
Device ID and Revision
Checksum Computation
2534h
2AC3h
3F7Fh
3FEFh
0030h
CODE PROTECTION DISABLED
DS41332C-page 23