DSPIC30F2011-20I/ML Microchip Technology, DSPIC30F2011-20I/ML Datasheet - Page 106
![IC DSPIC MCU/DSP 12K 28QFN](/photos/6/81/68120/150-28-qfn_sml.jpg)
DSPIC30F2011-20I/ML
Manufacturer Part Number
DSPIC30F2011-20I/ML
Description
IC DSPIC MCU/DSP 12K 28QFN
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F2011-20ISO.pdf
(66 pages)
2.DSPIC30F2011-20ISO.pdf
(210 pages)
3.DSPIC30F2011-20ISO.pdf
(14 pages)
4.DSPIC30F2011-20ISO.pdf
(6 pages)
5.DSPIC30F2011-20ISO.pdf
(18 pages)
6.DSPIC30F2011-20IP.pdf
(206 pages)
Specifications of DSPIC30F2011-20I/ML
Core Processor
dsPIC
Core Size
16-Bit
Speed
20 MIPS
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
12
Program Memory Size
12KB (4K x 24)
Program Memory Type
FLASH
Ram Size
1K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 8x12b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
Core Frequency
40MHz
Core Supply Voltage
5.5V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
12
Flash Memory Size
12KB
Supply Voltage Range
2.5V To 5.5V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
DAF30-4 - DEVICE ATP FOR ICE4000
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
DSPIC30F201120IML
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F2011-20I/ML
Manufacturer:
Microchip Technology
Quantity:
135
dsPIC30F2011/2012/3012/3013
15.3.4
The transmit interrupt flag (U1TXIF or U2TXIF) is
located in the corresponding interrupt flag register.
The transmitter generates an edge to set the UxTXIF
bit. The condition for generating the interrupt depends
on the UTXISEL control bit:
a)
b)
Switching between the two Interrupt modes during
operation is possible and sometimes offers more
flexibility.
15.3.5
Setting the UTXBRK bit (UxSTA<11>) will cause the
UxTX line to be driven to logic ‘0’. The UTXBRK bit
overrides all transmission activity. Therefore, the user
should generally wait for the transmitter to be Idle
before setting UTXBRK.
To send a Break character, the UTXBRK bit must be set
by software and must remain set for a minimum of 13
baud clock cycles. The UTXBRK bit is then cleared by
software to generate Stop bits. The user must wait for
a duration of at least one or two baud clock cycles in
order to ensure a valid Stop bit(s) before reloading the
UxTXB,
Transmission of a Break character does not generate a
transmit interrupt.
15.4
15.4.1
The following steps must be performed while receiving
8-bit or 9-bit data:
1.
2.
3.
4.
5.
DS70139F-page 106
If UTXISEL = 0, an interrupt is generated when
a word is transferred from the transmit buffer to
the Transmit Shift register (UxTSR). This means
that the transmit buffer has at least one empty
word.
If UTXISEL = 1, an interrupt is generated when
a word is transferred from the transmit buffer to
the Transmit Shift register (UxTSR) and the
transmit buffer is empty.
Set up the UART (see Section 15.3.1 “Trans-
mitting in 8-bit data mode”).
Enable the UART (see Section 15.3.1 “Trans-
mitting in 8-bit data mode”).
A receive interrupt will be generated when one
or more data words have been received, depend-
ing on the receive interrupt settings specified by
the URXISEL bits (UxSTA<7:6>).
Read the OERR bit to determine if an overrun error
has occurred. The OERR bit must be reset in soft-
ware.
Read the received data from UxRXREG. The act
of reading UxRXREG will move the next word to
the top of the receive FIFO, and the PERR and
FERR values will be updated.
Receiving Data
or
TRANSMIT INTERRUPT
TRANSMIT BREAK
RECEIVING IN 8-BIT OR 9-BIT
DATA MODE
starting
other
transmitter
activity.
15.4.2
The receive buffer is 4 words deep. Including the
Receive Shift register (UxRSR), the user effectively
has a 5-word deep FIFO buffer.
URXDA (UxSTA<0>) = 1 indicates that the receive
buffer has data available. URXDA = 0 implies that the
buffer is empty. If a user attempts to read an empty
buffer, the old values in the buffer will be read and no
data shift will occur within the FIFO.
The FIFO is reset during any device Reset. It is not
affected when the device enters or wakes up from a
Power Saving mode.
15.4.3
The receive interrupt flag (U1RXIF or U2RXIF) can be
read from the corresponding interrupt flag register. The
interrupt flag is set by an edge generated by the
receiver. The condition for setting the receive interrupt
flag
the URXISEL<1:0> (UxSTA<7:6>) control bits.
a)
b)
c)
Switching between the Interrupt modes during
operation is possible, though generally not advisable
during normal operation.
15.5
15.5.1
The OERR bit (UxSTA<1>) is set if all of the following
conditions occur:
a)
b)
c)
Once OERR is set, no further data is shifted in UxRSR
(until the OERR bit is cleared in software or a Reset
occurs). The data held in UxRSR and UxRXREG
remains valid.
If URXISEL<1:0> = 00 or 01, an interrupt is
generated every time a data word is transferred
from the Receive Shift register (UxRSR) to the
receive buffer. There may be one or more
characters in the receive buffer.
If URXISEL<1:0> = 10, an interrupt is generated
when a word is transferred from the Receive Shift
register (UxRSR) to the receive buffer, which as a
result of the transfer, contains 3 characters.
If URXISEL<1:0> = 11, an interrupt is set when
a word is transferred from the Receive Shift
register (UxRSR) to the receive buffer, which as
a result of the transfer, contains 4 characters
(i.e., becomes full).
The receive buffer is full.
The Receive Shift register is full, but unable to
transfer the character to the receive buffer.
The Stop bit of the character in the UxRSR is
detected, indicating that the UxRSR needs to
transfer the character to the buffer.
depends
Reception Error Handling
RECEIVE BUFFER (U
RECEIVE INTERRUPT
RECEIVE BUFFER OVERRUN
ERROR (OERR BIT)
on
the
© 2008 Microchip Technology Inc.
settings
X
RXB)
specified
by