DSPIC30F5016-30I/PT Microchip Technology, DSPIC30F5016-30I/PT Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
DSPIC30F5016-30I/PT
Manufacturer Part Number
DSPIC30F5016-30I/PT
Description
IC DSPIC MCU/DSP 66K 80TQFP
Manufacturer
Microchip Technology
Series
dsPIC™ 30Fr
Datasheets
1.DSPIC30F5016-30IPT.pdf
(230 pages)
2.DSPIC30F5016-30IPT.pdf
(14 pages)
3.DSPIC30F5016-30IPT.pdf
(6 pages)
4.DSPIC30F5016-30IPT.pdf
(18 pages)
Specifications of DSPIC30F5016-30I/PT
Core Processor
dsPIC
Core Size
16-Bit
Speed
30 MIPs
Connectivity
CAN, I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
Number Of I /o
68
Program Memory Size
66KB (22K x 24)
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
2K x 8
Voltage - Supply (vcc/vdd)
2.5 V ~ 5.5 V
Data Converters
A/D 16x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
80-TFQFP
Core Frequency
40MHz
Core Supply Voltage
5.5V
Embedded Interface Type
I2C, SPI, UART
No. Of I/o's
68
Flash Memory Size
66KB
Supply Voltage Range
2.5V To 5.5V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164320 - MODULE SKT MPLAB PM3 80TQFPAC30F007 - MODULE SKT FOR DSPIC30F 80TQFPDV164005 - KIT ICD2 SIMPLE SUIT W/USB CABLE
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
DSPIC30F501630IPT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DSPIC30F5016-30I/PT
Manufacturer:
MICROCHIP
Quantity:
624
Company:
Part Number:
DSPIC30F5016-30I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
DSPIC30F5016-30I/PT
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
dsPIC30F5015/5016
10. Motor Control PWM – PWM Counter Register
11. I/O Port – Port Pin Multiplexed with IC1
12. I
13. Timer Module
14. PLL Lock Status Bit
15. PSV Operations
16. I
17. I
18. I
The following sections describe the errata and work
around to these errata, where they may apply.
DS80247H-page 2
PTMR does not continue counting down after
halting code execution in Debug mode.
The Port I/O pin multiplexed with the Input Capture
1 (IC1) function cannot be used as a digital input
pin when the UART auto-baud feature is enabled.
When the I
addressing using the same address bits (A10 and
A9) as other I
not work as expected.
Clock switching prevents the device from waking
up from Sleep.
The PLL LOCK Status bit (OSCCON<5>) can
occasionally get cleared and generate an
oscillator failure trap even when the PLL is still
locked and functioning correctly.
An address error trap occurs in certain addressing
modes when accessing the first four bytes of any
PSV page.
The 10-bit slave does not set the RBF flag or load
the I2CxRCV register on address match if the
Least Significant bits of the address are the same
as the 7-bit reserved addresses.
When the I
slave with an address of 0x102, the I2CxRCV
register content for the lower address byte is 0x01
rather than 0x02.
When the I
device generates a glitch on the SDA and SCL
pins, causing a false communication start in a
single-master configuration or a bus collision in a
multi-master configuration.
2
2
2
2
C Module: 10-bit addressing mode
C Module: 10-bit Addressing Mode
C Module: 10-bit Addressing Mode
C Module
2
2
C module is enabled, the dsPIC
2
C module is configured as a 10-bit
C module is configured for 10-bit
2
C devices, the A10 and A9 bits may
®
DSC
1. Module: DISI Instruction
2. Module: Output Compare
When a user executes a DISI #7, for example,
this will disable interrupts for 7 + 1 cycles (7 + the
DISI instruction itself). In this case, the DISI
instruction uses a counter which counts down from
7 to 0. The counter is loaded with 7 at the end of
the DISI instruction.
If the user code executes another DISI on the
instruction cycle where the DISI state machine
does not properly re-engage and continue to
disable interrupts. At this point, all interrupts are
enabled. The next time the user code executes a
DISI instruction, the feature will act normally and
block interrupts.
In summary, it is only when a DISI execution is
coincident with the current DISI count = 0, that
the issue occurs. Executing a DISI instruction
before the DISI counter reaches zero will not
produce this error. In this case, the DISI counter
is loaded with the new value, and interrupts remain
disabled until the counter becomes zero.
Work around
When executing multiple DISI instructions within
the source code, make sure that subsequent DISI
instructions have at least one instruction cycle
between the time that the DISI counter
decrements to zero and the next DISI instruction.
Alternatively, make sure that subsequent DISI
instructions are called before the DISI counter
decrements to zero.
A glitch will be produced on an output compare pin
under the following conditions:
• The user software initially drives the I/O pin
• The output compare module is configured and
When these events occur, the output compare
module will drive the pin low for one instruction
cycle (T
Work around
None. However, the user may use a Timer
interrupt and write to the associated PORT register
to control the pin manually.
high using the output compare module or a
write to the associated PORT register.
enabled to drive the pin low at some later time
(OCxCON = 0x0002 or OCxCON = 0x0003).
CY
) after the module is enabled.
© 2008 Microchip Technology Inc.