PIC10F206-E/P Microchip Technology, PIC10F206-E/P Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC10F206-E/P
Manufacturer Part Number
PIC10F206-E/P
Description
IC PIC MCU FLASH 512X12 8DIP
Manufacturer
Microchip Technology
Series
PIC® 10Fr
Datasheets
1.PIC10F200T-IOT.pdf
(96 pages)
2.PIC10F200T-IOT.pdf
(6 pages)
3.PIC10F200T-IOT.pdf
(18 pages)
Specifications of PIC10F206-E/P
Core Size
8-Bit
Program Memory Size
768B (512 x 12)
Core Processor
PIC
Speed
4MHz
Peripherals
POR, WDT
Number Of I /o
3
Program Memory Type
FLASH
Ram Size
24 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
8-DIP (0.300", 7.62mm)
Controller Family/series
PIC10
No. Of I/o's
4
Ram Memory Size
24Byte
Cpu Speed
4MHz
No. Of Timers
1
Processor Series
PIC10F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
24 B
Interface Type
USB
Maximum Clock Frequency
4 MHz
Number Of Programmable I/os
4
Number Of Timers
1
Operating Supply Voltage
2 V to 5.5 V
Maximum Operating Temperature
+ 125 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With
AC162059 - HEADER INTRFC MPLAB ICD2 8/14PINAC164037 - MODULE SKT 6L PROMATE II SOT23
Eeprom Size
-
Data Converters
-
Connectivity
-
Lead Free Status / Rohs Status
Details
PIC10F200/202/204/206
3.1.2.5
The End Programming command terminates the
program process. A delay of T
required before the next command to allow the internal
programming voltage to discharge (see Figure 3-6).
FIGURE 3-6:
3.1.2.6
After this command is performed, the entire program
memory and Configuration Word is erased.
To perform a Bulk Erase of the program memory and
configuration fuses, the following sequence must be
performed (see Figure 3-12).
1.
2.
3.
4.
5.
DS41228E-page 6
Note 1: A fully erased part will read ‘1’s in every
Read and save 0x0FF/0x1FF oscillator calibra-
tion bits and 0x104/0x204 backup OSCCAL bits
into computer/programmer temporary memory.
Enter Program/Verify mode. PC is set to Config-
uration Word address.
Perform a Bulk Erase Program Memory
command.
Wait T
Restore OSCCAL bits.
2: The oscillator calibration bits are erased if
ICSPCLK
ICSPDAT
ERA
program memory location.
a Bulk Erase is invoked. They must be
read and saved prior to erasing the
device and restored during the program-
ming operation. Oscillator calibration bits
are stored at the Reset vector as the
operand of a MOVLW instruction.
End Programming
Bulk Erase Program Memory
to complete Bulk Erase.
END PROGRAMMING (EXTERNALLY TIMED)
DIS
1
0
(see Table 6-1) is
2
1
Preliminary
T
3
1
SET
1
4
1
To perform a full device Bulk Erase of the program
memory, configuration fuses, user IDs and backup
OSCCAL value, the following sequence must be
performed (see Figure 3-13).
1.
2.
3.
4.
5.
6.
7.
T
HLD
Read and save 0x0FF/0x1FF oscillator calibra-
tion bits and 0x104/0x204 backup OSCCAL bits
into computer/programmer temporary memory.
Enter Program/Verify mode.
Increment PC to 0x200/0x400 (first user ID
location).
Perform a Bulk Erase command.
Wait T
Restore OSCCAL bits.
Restore backup OSCCAL bits.
5
x
1
ERA
6
x
to complete Bulk Erase.
T
DIS
© 2007 Microchip Technology Inc.
1
Next Command
2